Memory Groups; Memory Group Assignment; Choosing The Desired Memory Group - Yaesu FT DX 3000 Operating Manual

M O
eMOry
Memory channels may be grouped into as many as six convenient batches, for easy identification and selection. For ex-
ample, you might want to designate memory groups for AM BC stations, short-wave broadcast stations, contest frequen-
cies, repeater frequencies and PMS limits, or any other groupings you like.
Each memory group is capable of holding up to 20 memory channels (except Memory Group 01: it is 19 memory chan-
nels, and the Group size is fixed). When a memory channel is grouped, the channel numbers change to correspond to the
chart below:

Memory Group Assignment

1. Press the [ MENU ] button to enter the Menu mode.
2. Rotate the [ CLAR/VFO-B ] knob (or press the p/q
button) to select Menu item "041 MEM GROUP".
3. Press the [ SELECT] button, then rotate the [ CLAR/
VFO-B ] knob (or press the p/q button) to set this
Menu item to "ENABLE" (the default setting is "DIS-
ABLE").
4. Press the [ SELECT ] button, then press the [ MENU ]
button to save the new setting and exit. Operation
will now be restricted to the six Memory Groups.
To cancel Memory Group operation, repeat steps (1)
through (4) above, choosing "DISABLE" in step (3).
a :
dviCe
To avoid confusion, note that the PMS memory group
and the PMS memories "P-1L" through "P-9U" will be
so designated.

Choosing the Desired Memory Group

You may recall memories just within a particular Memory Group, if desired.
1. Press the [ V/M ] button, if necessary, to enter the
"Memory" mode.
a :
dviCe
If you can not enter the "Memory" mode, check to
see if the transceiver is in VFO-B mode (the green
[ VFO-B ( RX )] Indicator/Switch is illuminated). If so,
press the [ VFO-A ( RX )] Indicator/Switch to return
operation to VFO-A. Now, press the [ V/M ] button to
enter the "Memory" mode.
2. Press and hold in the [ MCH/GRP ] button for one
second (located to the Lower right of the [ CLAR/
VFO-B ] knob). The imbedded LED inside the
switch will glow red.
3. Rotate the [ CLAR/VFO-B ] knob to select the de-
sired Memory Group.
4. Press the [ MCH/GRP ] button. The imbedded LED
inside the switch will glow orange.
5. Rotate the [ CLAR/VFO-B ] knob to select the de-
sired Memory Channel within the Selected Memory
Group.
a :
dviCe
If no channels have been assigned to a particular Memo-
ry Group, you will not have access to that Group.
Page 98
peraTiOn
M
eMory
g
rouPs
[ SELECT ] Button
[ MENU ] Button
M
eMory
g M "off"
rouP eMory
01 ~ 19
20 ~ 39
40 ~ 59
60 ~ 79
80 ~ 99
P-1L/1U ~ P-9L/9U
5M-01 ~ 5M-10
[ VFO-A ( RX )] Button
FT 3000 O
DX
[ CLAR/VFO-B ] Knob
C n
hannel uMBer
g M "on"
rouP eMory
1-01 ~ 1-19
2-01 ~ 2-20
3-01 ~ 3-20
4-01 ~ 4-20
5-01 ~ 5-20
P-1L/1U ~ P-9L/9U
US-1 ~ US-5
[ VFO-B ( RX )] Button
[ V/M ] Button
[ CLAR/VFO-B ] Knob
[ MCH/GRP ] Button
M
peraTing anual