Apf Width; Contour Level; If Notch Width - Yaesu FT DX 3000 Operating Manual
Hf/50 mhz transceiver
Hide thumbs
Also See for FT DX 3000:
- Operating manual (140 pages) ,
- Operating manual (140 pages) ,
- Operating manual (15 pages)
Table of Contents
Advertisement
105 LSB RX CARRIER
Function: Adjusts the receiver carrier point for the LSB
mode.
Available Values: -200 Hz ~ 0 ~ +200 Hz (10 Hz steps)
Default Setting: 0
106 USB RX CARRIER
Function: Adjusts the receiver carrier point for the USB
mode.
Available Values: -200 Hz ~ 0 ~ +200 Hz (10 Hz steps)
Default Setting: 0
RX DSP Group
107 APF WIDTH
Function: Selects the Bandwidth of the Audio Peak
Filter.
Available Values: NARROW/MEDIUM/WIDE
Default Setting: MEDIUM
108 CONTOUR LEVEL
Function: Adjusts the gain of the Contour filter.
Available Values: -40 ~ 0 ~ 20 dB
Default Setting: -15
109 CONTOUR SHIFT
Function: Adjusts the Q-factor of the Contour filter.
Available Values: 1 ~ 11
Default Setting: 10
110 DNR LEVEL
Function: Set the Digital Noise Reduction response.
Available Values: 1 ~ 15
Default Setting: 3
111 IF NOTCH WIDTH
Function: Selects the bandwidth of the DSP NOTCH
filter.
Available Values: NARROW / WIDE
Default Setting: WIDE
112 HF CW SHAPE
Function: Selects the passband characteristics of the
DSP filter for the CW mode on the HF band.
Available Values: SOFT / SHARP
Default Setting: SOFT
SOFT:
Primary importance is attached to the phase of
the filter factor.
SHARP: Primary importance is attached to the
amplitude of the filter factor.
113 HF CW SLOPE
Function: Selects the shape factor of the DSP filter for
the CW mode on the HF band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
FT
3000 O
DX
peraTing
M
anual
M
114 6M CW SHAPE
Function: Selects the passband characteristics of the
DSP filter for the CW mode on the 50 MHz band.
Available Values: SOFT / SHARP
Default Setting: SOFT
SOFT:
Primary importance is attached to the phase of
the filter factor.
SHARP: Primary importance is attached to the
amplitude of the filter factor.
115 6M CW SLOPE
Function: Selects the shape factor of the DSP filter for
the CW mode on the 50 MHz band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
116 HF PSK SHAPE
Function: Selects the passband characteristics of the
DSP filter for the PSK mode on the HF band.
Available Values: SOFT / SHARP
Default Setting: SHARP
SOFT:
Primary importance is attached to the phase of
the filter factor.
SHARP: Primary importance is attached to the
amplitude of the filter factor.
117 HF PSK SLOPE
Function: Selects the shape factor of the DSP filter for
the PSK mode on the HF band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
118 HF FSK SHAPE
Function: Selects the passband characteristics of the
DSP filter for the FSK mode on the HF band.
Available Values: SOFT / SHARP
Default Setting: SHARP
SOFT:
Primary importance is attached to the phase of
the filter factor.
SHARP: Primary importance is attached to the
amplitude of the filter factor.
119 HF FSK SLOPE
Function: Selects the shape factor of the DSP filter for
the PSK mode on the HF band.
Available Values: STEEP / MEDIUM / GENTLE
Default Setting: MEDIUM
120 HF SSB SHAPE
Function: Selects the passband characteristics of the
DSP filter for the SSB mode on the HF band.
Available Values: SOFT / SHARP
Default Setting: SHARP
SOFT:
Primary importance is attached to the phase of
the filter factor.
SHARP: Primary importance is attached to the
amplitude of the filter factor.
M
enu
ODe
Page 121
Advertisement
Chapters
Table of Contents
