Emergency Selcall - Icom IC-F7000 Instruction Manual

4
SELCALL/ALE OPERATION
ï Emergency selcall
The Emergency call allows you to broadcast an emer-
gency signal with own position information.
• Preparation for Emergency selcall
Sending a Selective Beacon call on several Selcall
channels, and check the propagation on each chan-
nel to select the channel of good signal quality. (p. 20)
• Sending Emergency selcall
q Push [∫ ∫ ] or [√ √ ] to select the desired channel for

Emergency selcall.

SELCALL
USB-A
RX--3.200.0
w Push [CALL] momentarily to enter the Call menu.
--2020:SELCALL
--TX:-3.200.0
--SelfID:1004
ç-SELCALL------------å
è-ID:1024
e Push [Ω Ω CLR] or [OK ≈ ≈ ] to select 'EMER SEL-
CALL.'
• 'SELCALL,' 'GPS BCON,' 'GPS POSN,' 'EMER SEL-
CALL,' 'PAGECALL,' 'STATUS CALL,' 'SEL BCON' are
selectable.
--2020:SELCALL
--TX:-3.200.0
--SelfID:1004
ç-EMER-SELCALL-------å
è-ID:1024
r Push [√ √ ] to select 'ID,' then edit
select an intended ID.
specified ID or
• Last selected ID is displayed.
• Enter the 4-digits (or 6-digits depending on Initial set
mode setting) number of the desired ID using 10-key-
pad directly. Or push [OK ≈ ≈ ] to enter ID selection, push
[∫ ∫ ]/[√ √ ] to select the pre-programmed ID, then push
[OK ≈ ≈ ] to fix the ID.
To send a group call, the last 2 digits to '0,' '0.'
To send a all call, the last 3 digits to '0,' '0,' '0.'
-*2020:SELCALL
--TX:-3.200.0
--SelfID:1004--------å
ç-EMER-SELCALL--
è*ID:0000------------å
t Push [C C A A L L L L ] for 1 sec. to transmit the Emergency
selcall.
• Before transmitting the selcall, verify 'SelfID' for your
own ID.
• While calling, push [CALL] to cancel the call.
27
HI
12:34
'0,' '0,' '0,' '0' as no
• Other than AUS version
q Push [E E M M G G ] momentarily to enter the Emergency
Call channel group.
[EMG]
w Push [∫ ∫ ] or [√ √ ] to select the channel.
EMERGENCY CALL
-*2010-EMER1---------å
-*2060-EMER2
ç*2070-EMER3----å
è--
e Push [E E M M G G ] for 2 sec. to transmit the Emergency
Selcall.
<Emergency Selcall menu>
After selecting the channel at step w, push
edit the Emergency selcall menu.
-*2010:EMER1---------å
--TX:20.500.0
--SelfID:1004
ç-EMER-SELCALL-------å
è*ID:0000
• Receiving Emergency Call
When a transceiver receives an Emergency Call with
your individual ID, it automatically responds by trans-
mitting. The receiving Emergency Call is stored in the
selcall memory.
After receiving a Emergency Call and push [Ω Ω CLR]
or [OK ≈ ≈ ] to select the call, the following indication is
displayed.
MES.20-01--------12:40
Emergency---------1006
-34"35'S--------
130"30'E--------å
-12:39
[∫]/[√]
to
[OK ≈ ≈ ]