HP 6125XLG Configuration Manual page 57

[SwitchA-maptbl-out-dot1p-lp] import 3 export 3
[SwitchA-maptbl-out-dot1p-lp] quit
# Enable byte-count WRR on Ten-GigabitEthernet 1/1/5 and Ten-GigabitEthernet 1/1/6, and
configure queue 3 to use SP queuing.
[SwitchA] interface ten-gigabitethernet 1/1/5
[SwitchA-Ten-GigabitEthernet1/1/5] qos wrr byte-count
[SwitchA-Ten-GigabitEthernet1/1/5] qos wrr 3 group sp
[SwitchA-Ten-GigabitEthernet1/1/5] quit
[SwitchA] interface ten-gigabitethernet 1/1/6
[SwitchA-Ten-GigabitEthernet1/1/6] qos wrr byte-count
[SwitchA-Ten-GigabitEthernet1/1/6] qos wrr 3 group sp
[SwitchA-Ten-GigabitEthernet1/1/6] quit
# Enable Ten-GigabitEthernet 1/1/5 and Ten-GigabitEthernet 1/1/6 to automatically negotiate
with their peers to decide whether to enable PFC, enable PFC for 802.1p priority 3, and configure
the two interfaces to trust the 802.1p priority carried in packets.
[SwitchA] interface ten-gigabitethernet 1/1/5
[SwitchA-Ten-GigabitEthernet1/1/5] priority-flow-control auto
[SwitchA-Ten-GigabitEthernet1/1/5] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet1/1/5] qos trust dot1p
[SwitchA-Ten-GigabitEthernet1/1/5] quit
[SwitchA] interface ten-gigabitethernet 1/1/6
[SwitchA-Ten-GigabitEthernet1/1/6] priority-flow-control auto
[SwitchA-Ten-GigabitEthernet1/1/6] priority-flow-control no-drop dot1p 3
[SwitchA-Ten-GigabitEthernet1/1/6] qos trust dot1p
[SwitchA-Ten-GigabitEthernet1/1/6] quit
# Create interface VFC 1, and configure it to operate in F mode.
[SwitchA] interface vfc 1
[SwitchA-Vfc1] fc mode f
# Bind interface VFC 1 to interface Ten-GigabitEthernet 1/1/5, and assign it to VSAN 10 as a
trunk port.
[SwitchA-Vfc1] bind interface ten-gigabitethernet 1/1/5
[SwitchA-Vfc1] port trunk vsan 10
[SwitchA-Vfc1] quit
# Assign interface Ten-GigabitEthernet 1/1/5 to VLAN 10 as a trunk port.
[SwitchA] interface ten-gigabitethernet 1/1/5
[SwitchA-Ten-GigabitEthernet1/1/5] port link-type trunk
[SwitchA-Ten-GigabitEthernet1/1/5] port trunk permit vlan 10
[SwitchA-Ten-GigabitEthernet1/1/5] quit
# Create interface VFC 2, and configure it to operate in F mode.
[SwitchA] interface vfc 2
[SwitchA-Vfc2] fc mode f
# Bind interface VFC 2 to interface Ten-GigabitEthernet 1/1/6, and assign it to VSAN 20 as a
trunk port.
[SwitchA-Vfc2] bind interface ten-gigabitethernet 1/1/6
[SwitchA-Vfc2] port trunk vsan 20
[SwitchA-Vfc2] quit
# Assign interface Ten-GigabitEthernet 1/1/6 to VLAN 20 as a trunk port.
51