Toshiba GR200 Series Instruction Manual page 1086

Binary output circuit
5.4.4
Either a CPL logic or a PLC signal can drive a binary output circuit. Table 5.4-9 shows the
settings summary of CPL function.
Setting items
BO1_CPL
BO1 Input signal1
Input signal2
Input signal3
Input signal4
Input signal5
Input signal6
Input signal7
Input signal8
LOGIC-SW
On Delay Timer
Off Delay Timer
INVERSE-SW
TIMER-SW
Logic Timer
Reset signal
BO2_CPL
BO2 Input signal1
.....
Input signal8
LOGIC-SW
On Delay Timer
Off Delay Timer
INVERSE-SW
TIMER-SW
Logic Timer
Reset signal
.....
BO n _CPL
n
BO Input signal1
.....
Input signal8
LOGIC-SW
On Delay Timer
Off Delay Timer
INVERSE-SW
TIMER-SW
Logic Timer
Reset signal
Note: The user can set a reset signal and eight input signals with Data IDs. Data IDs
1
are listed as a signal monitoring point for each function. Setting items are
summarized in each slot. (See sections 5.4.8(i) and 5.4.8(ii))
Table 5.4-9 Setting items for binary output circuits
Setting-range or
Data_ID
Off / On
(Preferred Data ID)
(Preferred Data ID)
(Preferred Data ID)
(Preferred Data ID)
(Preferred Data ID)
(Preferred Data ID)
(Preferred Data ID)
(Preferred Data ID)
AND/OR/XOR
0.000 to 300.000
0.000 to 300.000
Normal / Inverse
OFF/Delay/Dwell/Latch
0.000 to 300.000
(Preferred Data ID)
Off / On
(Preferred Data ID)
.....
(Preferred Data ID)
AND/OR/XOR
0.000 to 300.000
0.000 to 300.000
Normal / Inverse
OFF/Delay/Dwell/Latch
0.000 to 300.000
(Preferred Data ID)
Off / On
(Preferred Data ID)
.....
(Preferred Data ID)
AND/OR/XOR
0.000 to 300.000
0.000 to 300.000
Normal / Inverse
OFF/Delay/Dwell/Latch
0.000 to 300.000
(Preferred Data ID)
- 1063 -
Contents
– Switch On for programmable operation
– Set a Data ID at the first input on BO1.
– Set a Data ID at the second input on BO1.
– Set a Data ID at the third input on BO1.
– Set a Data ID at the forth input on BO1.
– Set a Data ID at the fifth input on BO1.
– Set a Data ID at the sixth input on BO1.
– Set a Data ID at the seventh input on BO1.
– Set a Data ID at the eighth input on BO1.
– Switch for logic-gate operation on BO1
s Set a value for an on-delay-timer on BO1
s Set a value for an off-delay-timer on BO1
s Inversion operation of BO1 signal
– Selection of a type in the delay timer on BO1
s Setting Off Delay Timer for Delay and Dwell
– Setting Data ID for Latch
– Switch On for programmable operation
– Set a Data ID at the first input on BO2.
.....
– Set a Data ID at the eighth input on BO2
– Switch for logic-gate operation on BO2
s Set a value for an on-delay-timer on BO2
s Set a value for an off-delay-timer on BO2
– Inversion operation of BO2 signal
– Selection of a type in the delay timer on BO2
s Setting Off Delay Timer for Delay and Dwell
– Setting Data ID for Latch
– Switch On for programmable operation
– Set a Data ID at the first input on BO
.....
– Set a Data ID at the eighth input on BO
– Switch for logic-gate operation on BO
s Set a value for an on-delay-timer on BO
s Set a value for an off-delay-timer on BO
– Inversion operation of BO
– Selection of a type in the delay timer on BO
s Setting Off Delay Timer for Delay and Dwell
– Setting Data ID for Latch
6F2S1914 (0.49)
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Not assigned
Normal
Not assigned
Not assigned
Not assigned
Normal
Not assigned
n
Not assigned
n Not assigned
n
n
n
n signal Normal
n
Not assigned
GRL200 (Soft 033 & 037)
Default
Off
1
1
1
1
1
1
1
1
AND
0.000
0.000
OFF
0.000
1
Off
1
.....
1
AND
0.000
0.000
OFF
0.000
1
Off
1
.....
1
AND
0.000
0.000
OFF
0.000
1