Mitsubishi Electric NZ2GFCF-D62PD2 User Manual page 42

Signal direction: High-speed counter module 
Module
type
Device
number
CH1 Measured pulse value update flag reset
RX31
completed (Function input terminal)
CH1 Measured pulse value update flag
RX32
(Function input terminal)
CH1 Measured pulse value update flag reset
RX33
completed (Latch counter input terminal)
CH1 Measured pulse value update flag (Latch
RX34
counter input terminal)
CH1 ON width setting change completed (PWM
RX35
output)
RX36 CH1 Error status
RX37 CH1 Warning status
RX38 Use prohibited
RX39 CH2 Preset/replace completion
RX3A Use prohibited
CH2 External preset/replace (Z Phase) request
RX3B
detection
RX3C Use prohibited
RX3D CH2 Counter function detection
RX3E CH2 Cam switch execute/PWM output
CH2 Setting change completed (Sampling
RX3F
Main
counter/Periodic pulse counter)
module
CH2 Update flag reset completed (Latch count
RX40 value/Sampling count value/Periodic pulse
count value)
CH2 Update flag (Latch count value/Sampling
RX41
count value/Periodic pulse count value)
CH2 Latch count value update flag reset
RX42
completed (Latch counter input terminal)
CH2 Latch count value update flag (Latch
RX43
counter input terminal)
CH2 Update flag reset completed (Measured
RX44
frequency value/Measured rotation speed value)
CH2 Update flag (Measured frequency
RX45
value/Measured rotation speed value)
RX46 Use prohibited
RX47 Use prohibited
RX48 Use prohibited
CH2 Measured pulse value update flag reset
RX49
completed (Function input terminal)
CH2 Measured pulse value update flag
RX4A
(Function input terminal)
CH2 Measured pulse value update flag reset
RX4B
completed (Latch counter input terminal)
40
Remote input
Master/local module
Description
Remote output
Signal direction: Master/local module  High-
speed counter module
Device
number
CH1 Measured pulse value update flag reset
RY31
command (Function input terminal)
CH1 Pulse measurement start command (Latch
RY32
counter input terminal)
CH1 Measured pulse value update flag reset
RY33
command (Latch counter input terminal)
RY34 Use prohibited
CH1 ON width setting change request (PWM
RY35
output)
RY36 CH1 Error reset command
RY37 Use prohibited
RY38 CH2 Coincidence output enable command
RY39 CH2 Preset/replace command
RY3A CH2 Count down command
CH2 External preset/replace (Z Phase) request
RY3B
detection reset command
RY3C CH2 Count enable command
RY3D CH2 Selected counter function start command
CH2 Cam switch execute command/PWM
RY3E
output start command
CH2 Setting change request (Sampling
RY3F
counter/Periodic pulse counter)
CH2 Update flag reset command (Latch count
RY40 value/Sampling count value/Periodic pulse
count value)
RY41 Use prohibited
CH2 Latch count value update flag reset
RY42
command (Latch counter input terminal)
RY43 Use prohibited
CH2 Update flag reset command (Measured
RY44
frequency value/Measured rotation speed value)
RY45 Use prohibited
RY46 Use prohibited
RY47 Use prohibited
CH2 Pulse measurement start command
RY48
(Function input terminal)
CH2 Measured pulse value update flag reset
RY49
command (Function input terminal)
CH2 Pulse measurement start command (Latch
RY4A
counter input terminal)
CH2 Measured pulse value update flag reset
RY4B
command (Latch counter input terminal)
Description