Furuno FCV-600 Installation Manual
  1. Manuals
  2. Brands
  3. Furuno Manuals
  4. Fish Finder
  5. FCV-600
  6. Installation manual
Furuno FCV-600 Installation Manual

Furuno FCV-600 Installation Manual

Hide thumbs Also See for FCV-600:
Table of Contents

Advertisement

Quick Links

Download this manual
SAFETY INSTRUCTIONS ................................................................................................ i
SYSTEM CONFIGURATIONS........................................................................................ iii
1. MOUNTING................................................................................................................. 1
1.1 Equipment List ......................................................................................................................1
1.2 Main Unit...............................................................................................................................3
1.3 Transducer (Option)..............................................................................................................8
2. WIRING..................................................................................................................... 20
2.1 Wiring..................................................................................................................................20
2.2 Data Sentences/PGN Data Sentences ...............................................................................25
3. INITIAL SETTINGS................................................................................................... 28
3.1 Language and Transducer Settings....................................................................................28
3.2 Input/Output Settings ..........................................................................................................29
3.3 Wireless LAN setup ............................................................................................................34
3.4 Calibration settings .............................................................................................................39
3.5 Heave Sensor Settings .......................................................................................................41
APPX. 1 INSTALLATION FOR TRANSDUCER (THRU-HULL MOUNT)................AP-1
APPX. 2 INSTALLATION OF 525STID-MSD ..........................................................AP-5
PACKING LIST(S) ....................................................................................................... A-1
OUTLINE DRAWING(S) .............................................................................................. D-1
INTERCONNECTION DIAGRAM(S) ........................................................................... S-1
All brand and product names are trademarks, registered trademarks or service marks of their respective holders.
Installation Manual
Model FCV-600/800
Link For Operator's Manual
Operator's Manual is available on
FURUNO website. Access and
download the manual from the
QR code on the right.
www.furuno.com
FISH FINDER

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FCV-600 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Furuno FCV-600

Summary of Contents for Furuno FCV-600

  • Page 1: Table Of Contents

    OUTLINE DRAWING(S) ....................D-1 INTERCONNECTION DIAGRAM(S) ................S-1 Link For Operator's Manual Operator's Manual is available on FURUNO website. Access and download the manual from the QR code on the right. www.furuno.com All brand and product names are trademarks, registered trademarks or service marks of their respective holders.

  • Page 2: Safety Instructions

    The installer is solely responsible for the Do not turn on the equipment with the transducer out of water. proper installation of the equipment. FURUNO will assume no responsibility for any damage associated with The transducer can be damaged. improper installation of the transducer.
  • Page 3 Do not remove the label. If the label is missing To avoid electrical shock, do not remove cover. Type: 16-021-3517-0 or damaged, contact a FURUNO agent or Code No.: 100-350-230-10 dealer about replacement. The TFT LCD is constructed using the latest LCD techniques, and displays 99.99% of its pixels.

  • Page 5: System Configurations

    Optional or local supply NMEA2000 Device GPS Receiver Satellite Compass 12-24VDC USB Flash memory For maintenance Wireless LAN Connection iOS/Android device FCV-600 unit Submonitor Transducer FCV-800 FISH FINDER FCV-800 Standard Supply Optional or local supply NMEA2000 Device GPS Receiver 12-24VDC...

  • Page 6: Mounting

    FRU-CCB12-DA-10M 001-608-450 10m, for transducer (12pin) FRU-MJ10CCB12-300 001-636-150 Converter Cable (10pin2 - 12pin), 0.3m, for dual frequen- cy CHIRP transducer, for FCV- FRU-CF-H07-02M 001-641-070 2m, for FCV-600 FRU-CF-H16-02M 001-641-080 2m, for FCV-800 NMEA Cable As- FRU-NMEA-PMMFF-010 001-533-060 sembly FRU-NMEA-PMMFF-020 001-533-070...
  • Page 7 1. MOUNTING Name Type Code No. Remarks Matching Box MB-1100 For CW 1kW transducers, For FCV-800 Flush Mount Kit OP02-89 001-638-230 For FCV-600 OP02-88 001-638-240 For FCV-800 Transducer 600W transducers 520-5PSD 520-5MSD 520-PLD 525-5PWD Transducer 600W transducers 525T-PWD 525T-BSD 525T-LTD/12...

  • Page 8: Main Unit

    1. MOUNTING Other compatible transducers (local supply) The transducers (Manufactured by AIRMAR Technology Corporation) listed in the ta- ble below are compatible with this equipment. Single Frequency CHIRP Output Power Type 300W B150M SS75L 600W B75M SS75M B785M SS75H TM165HW 1kw (FCV-800 only) B175M TM185M...
  • Page 9 1. MOUNTING 1.2.1 Desktop and bulkhead mount This unit is shipped with a hanger. Follow the steps below to mount the main unit on a desktop or bulkhead. The figures of FCV-800 are used in this section. 1. Unfasten the knobs on either side of the main unit and detach the unit from the hanger.
  • Page 10 For FCV-600 The below flush mount kit is required when flush mounting the unit. Kit details: OP02-89, Code No.: 001-638-230 Name Mounting template (for both FCV-600 and FCV-800 (double-sided printing)) Sponge V for F mount Sponge H for F mount...
  • Page 11 1. MOUNTING 6. Rotate the butterfly bolts and butterfly nuts attached to the flush mount F metal (two in total) to move the screw leg protector towards the mount F metal. Mount F metal Butterfly bolt (see the Note below). Butterfly nut Mount F metal assembly Screw leg protector...
  • Page 12 For FCV-800 The below flush mount kit is required when flush mounting the main unit. Kit details: OP02-88, Code No.: 001-638-240 Name Mounting template (for both FCV-600 and FCV-800 (double-sided printing)) Sponge V for F mount Sponge H for F mount Binding screw 1.

  • Page 13: Transducer (Option)

    1. MOUNTING 8. Use the four binding screws (φ5×20) and fasten the main unit. 9. Place the screw covers back to the each corner of the unit. Push the screw covers in order until they click into their Side place, first on the front and then on the sides (two locations). Front There is no "click"...
  • Page 14 1. MOUNTING 1.3.1 Thru-hull mount 520-PLD For details of the installation, see the transducer manual. Transducer mounting location (for 520-5PSD/520-5MSD) The thru-hull mount transducer provides the best performance of all, since the trans- ducer protrudes from the hull and the effect of air bubbles and turbulence near the hull skin is reduced.
  • Page 15 1. MOUNTING turbed flow of water around the transducer. The fairing block should be smaller than the transducer itself to provide a channel to divert turbulent water around the sides of the transducer rather than over its face. 3. Drill a hole just large enough to Hole for pass the threaded stuffing tube of stuffing tube...
  • Page 16 1. MOUNTING 1.3.2 Transom mount transducer The optional transom mount transducer is very commonly employed, usually on rela- tively small I/O or outboard boats. Do not use this method on an inboard motor boat because turbulence is created by the propeller ahead of the transducer. Parallel with hull Transom Less than 10°...
  • Page 17 1. MOUNTING 1.3.3 How to mount a Thru-hull transducer inside the hull The thru-hull mount transducer may also be installed inside the hull on FRP boats. However, this installation method affects the ability to detect the bottom, fish and other objects because the ultrasound pulse is weakened when it passes through the hull.
  • Page 18 1. MOUNTING 2. Decide the most suitable site from the selected locations by doing the following: 1) Refer to section 2.1 for connecting the power cable and transducer cable to the main unit. 2) Put the transducer into a water-filled plastic bag. Press the transducer against the chosen site.
  • Page 19 8) Set the value as ‘‘+20‘‘ and press the KNOB. 9) If multiple CW/CHIRP transducers are shown, repeat step 7. 10) For FCV-600, select [Bottom Level XDR] and press the KNOB. For FCV-800, select [Bottom Level XDR1] and press the KNOB.
  • Page 20 1. MOUNTING 1.3.4 Mounting of 525STID-MSD/525STID-PWD transducers (speed/ temperature sensors) Note: DO NOT overtighten screws. They may be damaged. 525STID-MSD The optional transducer 525STID-MSD is designed for thru-hull mounting. For mount- ing, see section 1.3.1. φ 79 133 2.00"-12 UN threads φ...
  • Page 21 1. MOUNTING NOTICE Do not mount the sensor in an area of turbulence or bubbles: - near water intake or discharge openings - behind strakes, struts, fittings, or hull irregularities - behind eroding paint (an indication of turbulence). Avoid mounting the sensor where the boat may be supported during trailering, launching, hauling, and storage.
  • Page 22 1. MOUNTING If you do not know the transom angle, temporarily attach the bracket and sensor to the transom to determine if the plastic shim is needed. Adjustments 1. Using a straight edge, sight the underside of the sensor relative to the underside of the hull.
  • Page 23 1. MOUNTING 5. Using the vertical adjustment space on the bracket slots, slide the sensor up or down to provide a projection of Cable cover 3 mm (1/8"). Cable 6. Tighten the self tapping screws. clamp 50 mm (2") Hull projection 3 mm (1/8") 3 mm Step 2...
  • Page 24 1. MOUNTING 5. Apply marine sealant to the threads of the #6 x 1/2" self-tapping screw to prevent water from seeping into the transom. If you have drilled a hole through the tran- som, apply marine sealant to the space around the cable where it passes through the transom.

  • Page 25: Wiring

    To inboard grounding USB port For maintenance PWR/NMEA0183 port XDR port NMEA2000 port To transducer To NMEA2000 device 12-24VDC Back side of FCV-600 Ground terminal To inboard grounding USB port For maintenance PWR/KP/NMEA0183 port XDR1/XDR2 port NMEA2000 port 12-24VDC, to NMEA0183 device...
  • Page 26 2. WIRING 2.1.1 Power/data cable and ground wiring For FCV-600, connect the supplied FRU-CF-H07-02M cable (2m, single ended con- nector) to the [PWR/NMEA0183] port. For FCV-800, connect the supplied FRU-CF-H16-02M cable (2m, single ended con- nector) to the [PWR/KP/NMEA0183] port.
  • Page 27 KP. 2.1.2 Transducer cable connection For FCV-600, connect the transducer cable to the [XDR] port. For FCV-800, the type and combination of transducer determines the port to which the transducer cable is connected. Note: Supply voltages are different depending on XDR ports. Be sure to connect each transducer to the correct port (see the table below).
  • Page 28 2. WIRING Transducer Connection port Dual frequency CHIRP transducer connection*. [XDR1], [XDR2] Compatible transducers: B265LH-FJ12, TM265LH-FJ12, CM265LH-FJ12, etc. Simultaneous connection of single frequency (LF) CHIRP and single [XDR1]: CHIRP (LF) frequency (MF/HF) CHIRP transducers. [XDR2]: CHIRP (MF/HF) Compatible transducers: Only in the below combinations •...
  • Page 29 2. WIRING Jumper block setting Transducer J2: No output reduction (default) 50B-6/6B J1: Output reduction 02P6348 50kHz Green (shield) SHIELD 200kHz Connect 10P connector to XDR port on rear of Detach grommet; display unit. Transducer attach cord lock. 200B-5S 2.1.3 NMEA2000 device connection Use the optional FRU-NMEA-PMMFF cable (1m, 2m, 6m, both end connectors) or FRU-NMEA-PFF (1m, 2m, 6m, single end connector) to connect to the backbone of...

  • Page 30: Data Sentences/Pgn Data Sentences

    Water speed and heading Ver. 1.5/2.0/3.0/4.0/4.1 Course over ground and ground speed Ver. 1.5/2.0/3.0/4.0/4.1 Cross track error Ver. 1.5/2.0/3.0/4.0/4.1 Time and date Ver. 1.5/2.0/3.0/4.0/4.1 GPatt FURUNO original sentence GPhve FURUNO original sentence pireq FURUNO original sentence Order of priority Data Priority Latitude/Longitude: GNS>GGA>RMC>RMA>GLL...
  • Page 31 Water temperature Ver. 1.5/2.0/3.0/4.0/4.1 Recommended minimum navigation information Ver. 1.5/2.0/3.0/4.0/4.1 Target position Ver. 3.0/4.0/4.1 Speed through the water Ver. 1.5/2.0/3.0/4.0/4.1 pidat FURUNO original sentence SDbhr FURUNO original sentence SDmrk FURUNO original sentence SDtbd FURUNO original sentence SDtfl FURUNO original sentence 2.2.2...
  • Page 32 Environmental Parameters - DEPRECATED 130312 Temperature - DEPRECATED 130314 Actual Pressure 130316 Temperature, Extended Range 130577 Direction Data 130821 FURUNO original PGN output PGN PGN name Transmission Interval (msec) 059392 ISO Acknowledgement 059904 ISO Request 060928 ISO Address Claim 061184...

  • Page 33: Initial Settings

    Continue the procedure to select the transducer. 3. Select [XDR Type] (for FCV-600) or [XDR1 Type] (for FCV-800) and press the KNOB. For FCV-600 For FCV-800 4.

  • Page 34: Input/Output Settings

    3. INITIAL SETTINGS is not shown on the list in step 3, depending on the transmission output, select [600W] or [1kW] (for FCV-800 only). Note 1: Make sure to select the appropriate transducer. Otherwise the connected transducer will be damaged. Note 2: You can view and modify transducer settings on the [Transducer] menu from the [System] menu (see Operator‘s Manual for further information).
  • Page 35 [PWR/KP/NMEA0183] port. • [Own], [Own1] (for FCV-800 only): Data is imported from transducer connect- ed to the [XDR] (for FCV-600) or [XDR1] (for FCV-800) port. • [Own2] (for FCV-800 only): Data is imported from transducer connected to [XDR2] port.
  • Page 36 3. INITIAL SETTINGS [Sensor In Use] list You can check the data sources of the currently used sensors in the [Sensor In Use] of the [Network] menu. If no data is entered, [--------] will be displayed. Example of FCV-800 display 3.2.2 NMEA0183 port settings (FCV-800 only) Adjust the nav equipment settings connected to the [PWR/KP/NMEA0183] port.
  • Page 37 • [Off]: Do not output latitude/longitude. • [TLL]: Output latitude/longitude. • [FURUNO-TLL]: Output latitude/longitude, depth and water temperature. Requires [FURUNO-TLL] enabled device. [Bottom Hardness] Shown only when the transducer that supports hardness* is connected. Select [On] to output the hardness sentence (SDbhr).
  • Page 38 3. INITIAL SETTINGS 4. Select [Device List] to show the list of other connected equipments and press the KNOB. Select the device from the list and press the KNOB to show the [Device Info] display. PG-700 26844 Device List Refresh Select the device name PG-700...

  • Page 39: Wireless Lan Setup

    Wireless LAN setup When connected to wireless LAN, the following operations become available: • View FCV-600 or FCV-800 fish finder images and voyage information on your iOS or Android™ device (for iOS: only one device can be connected). • Use the FCV main unit* as a sub monitor (only one sub-monitor can be connected).
  • Page 40 3. INITIAL SETTINGS 4. Select [Wireless LAN Setting] and press the KNOB. 5. Select [Wireless LAN] and press the KNOB. 6. Select [On] and press the KNOB. 7. Select [Mode] and press the KNOB. 8. Select [Master] and press the KNOB. 9.
  • Page 41 3. INITIAL SETTINGS 3) Change to the desired name (maximum 32 characters). a) Select the typing mode (abc, ABC, ?123, ~[<) and press the KNOB. Text entry cursor Typing mode Typing mode: Alphabet (lowercase letters) Typing mode: Alphabet (uppercase letters) Typing mode: Numerical Typing mode: Symbol b) Select a character and press the KNOB.
  • Page 42 3. INITIAL SETTINGS For [Client Mode] 1) Select [Connect Network Setting] and press the KNOB. 2) With [Available Network] selected, press the KNOB.When an available network near the unit is detected, the name of the network is displayed in the [Network List] window.
  • Page 43 3. INITIAL SETTINGS For sub monitor 1. Press the MENU/ESC key to show the main menu. 2. Select [Network] and press the KNOB. 3. Select [Wireless LAN] and press the KNOB. 4. Select [Use Sub Sets] and press the KNOB. 5.

  • Page 44: Calibration Settings

    3. INITIAL SETTINGS 3.3.2 LAN settings on the sub monitor side Do the following procedure when using the FCV as a sub monitor. 1. Press the MENU/ESC key to show the main menu. 2. Select [Network] and press the KNOB. 3.
  • Page 45 Compensates the NMEA0183 output hardness value. [Bottom Hardness] [Heave Sensor Setting] See section 3.5. : The items displayed will vary depending on the connected transducer. : Displayed for FCV-600 only. : Displayed for FCV-800 only. 4. Press the MENU/ESC key twice to close the menu.

  • Page 46: Heave Sensor Settings

    3. INITIAL SETTINGS Heave Sensor Settings [Heaving Sensor Setting] window allows you to adjust settings related to heaving com- pensation. Note 1: Satellite Compass™ connection is required to use the heaving correction function. If no hull motion information is input from the Satellite Compass™, the heave sensor compensation function cannot be used.
  • Page 47 STERN 12. See the figure above to enter the location information of the transducer connected to the [XDR] (FCV-600) or [XDR1] (FCV-800) port. Set the position of the trans- ducer ([Bow/Stern] [Up/Down] [Port/Starboard]) as measured from the reference point ("0"). Port is "-" and starboard is "+".
  • Page 57 12/Mar/2015 H.MAKI...
  • Page 60 When a claim is made, FURUNO has a right to choose whether with other electronic devices. The imported product may also be to repair the product or replace it.
  • Page 61 24 months from installation date provided the work is done by Furuno U.S.A., Inc. or an AUTHORIZED Furuno dealer during normal shop hours and within a radius of 50 miles of the shop location.
  • Page 64 ・FURUNO Authorized Distributor/Dealer 9-52 Ashihara-cho, Nishinomiya, 662-8580, JAPAN A : JAN 2023 Printed in Japan All rights reserved. A1 : JUN . 08, 2023 Pub. No. IME-23940-A1 (YOSH ) FCV-600/FCV-800 0 0 0 2 0 0 0 1 3 1 0...

This manual is also suitable for:

Fcv-800

Table of Contents