Table of Contents
Advertisement
→
Pos : 124 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/060 Betrieb_Spi nc ontr ol L+S/Spinc ontrol L (Z ent6) /060- 0030-0020 M anueller Betri eb @ 27\m od_1405319254192_68.docx @ 192647 @ 3 @ 1
6.3.2
Manual mode
Pos : 125 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/060 Betrieb_Spi nc ontr ol L+S/Spinc ontrol L (Z ent6) /060- 0030-0020- 0010 Starten ei ner Z entrifugati on @ 27\m od_1405319255424_68.docx @ 192661 @ 4 @ 1
→
6.3.2.1
Starting a centrifugation run
Pos : 126 /010 Univ ers almodul e/
Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1
Pos : 127 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/060 Betrieb_Spi nc ontr ol L+S/Spinc ontrol L (Z ent6) /060- 0030-0020- 0020 U nterbr ec hen einer Z entrifug ation @ 27\mod_1405319256724_68.doc x @ 192675 @ 4 @ 1
→
6.3.2.2
Interrupting a centrifugation run
Pos : 128 /010 Univ ers almodul e/
Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1
Pos : 129 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/060 Betrieb_Spi nc ontr ol L+S/Spinc ontrol L (Z ent6) /060- 0030-0020- 0030 U nterbr ec hen eines Brems vorgangs @ 27\m od_1405319258018_68.docx @ 192689 @ 4 @ 1
→
6.3.2.3
Interrupting a deceleration process
Pos : 130 /010 Univ ers almodul e/
Leerz eile @ 0\mod_1202116244500_0.docx @ 114 @ @ 1
Pos : 131 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/060 Betrieb_Spi nc ontr ol L+S/Spinc ontrol L (Z ent6) /060- 0030-0020- 0040 Auswahl, Anzeig e und Änderung von D aten @ 27\m od_1405319259317_68.docx @ 192703 @ 4 @ 1
→
6.3.2.4
Selection, display, and modification of data
Pos : 132 /010 Univ ers almodul e/
Seitenwechs el @ 0\mod_1202116244312_0.docx @ 105 @ @ 1
Version 08/2012, Rev. 1.24 of 28/04/2022 • sb
Translation of the original operating manual, part no. 0700702
The centrifuge is ready for operation when the start key is illuminated.
•
Press the start key in order to start a centrifugation run.
•
Press the stop key in order to interrupt a centrifugation run. The
centrifugation run will be terminated prematurely.
Quick stop
•
Press the stop key for more than two seconds.
The centrifuge decelerates with the maximum deceleration curve.
After a quick stop, the centrifuge lid must be opened before a new
centrifugation run can be started.
A quick stop can also be triggered during a normal deceleration, e.g. in
order to speed up the deceleration.
When a quick stop is triggered, "fast" will be displayed in the lower right-
hand corner of the display.
•
Press the start key during a deceleration process in order to interrupt it
and to restart the centrifuge.
•
Turn the function knob in order to select a field. The selected field will
be preceded by the indication "set", "run", or "save".
•
Press the function knob. The indication ("set", "run", or "save") flashes
and the modification mode is active.
•
Turn the function knob in order to modify the set value of the selected
field.
•
Press the function knob again to confirm the input and to quit the
modification mode
•
The process will be interrupted if the stop key is pressed or after 60
seconds without any further input.
Refrigerated Centrifuge Sigma 2-16KL
6 Using the centrifuge
37 / 82
Advertisement
Table of Contents
