Table of Contents
Advertisement
→
Pos : 119 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/062 Betrieb_Spi nc ontr ol Eas y+Univ ersal/Spinc ontrol Univ ersal /062- 0030-0020 M anueller Betri eb @ 28\m od_1405320526938_68.docx @ 194439 @ 3 @ 1
6.3.2
Manual mode
Pos : 120 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/062 Betrieb_Spi nc ontr ol Eas y+Univ ersal/Spinc ontrol Univ ersal /062- 0030-0020-0010 Starten ei ner Z entrifugati on @ 28\m od_1405320527735_68.docx @ 194453 @ 4 @ 1
→
6.3.2.1
Starting a centrifugation run
Pos : 121 /010 Univ ers almodul e/
Leerzeil e 8pt @ 12\m od_1337063062114_0.docx @ 65687 @ @ 1
→
Pos : 122 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/062 Betrieb_Spi nc ontr ol Eas y+Univ ersal/Spinc ontrol Univ ersal /062- 0030-0020-0020 U nterbr ec hen einer Z entrifug ation @ 28\mod_1405320528561_68.doc x @ 194467 @ 4 @ 1
6.3.2.2
Interrupting a centrifugation run
Pos : 123 /010 Univ ers almodul e/
Leerzeil e 8pt @ 12\m od_1337063062114_0.docx @ 65687 @ @ 1
Pos : 124 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/062 Betrieb_Spi nc ontr ol Eas y+Univ ersal/Spinc ontrol Univ ersal /062- 0030-0020-0030 U nterbr ec hen eines Brems vorgangs @ 28\m od_1405320529412_68.docx @ 194481 @ 4 @ 1
→
6.3.2.3
Interrupting a deceleration process
Pos : 125 /010 Univ ers almodul e/
Leerzeil e 8pt @ 12\m od_1337063062114_0.docx @ 65687 @ @ 1
Pos : 126 /100 Sigma/100 BA Z entrifugen Sigma (Standardm odul e)/062 Betrieb_Spi nc ontr ol Eas y+Univ ersal/Spinc ontrol Univ ersal /062- 0030-0020-0040 Auswahl, Anzeig e und Änderung von D aten @ 28\m od_1405320530250_68.docx @ 194495 @ 4 @ 1
→
6.3.2.4
Selection, display, and modification of data
Pos : 127 /010 Univ ers almodul e/
Leerzeil e 8pt @ 12\m od_1337063062114_0.docx @ 65687 @ @ 1
Pos : 128 /100 Sigma/100 BA Z entrifug en Sigma (Standardm odul e)/062 Betrieb_Spi nc ontr ol Eas y+Univ ersal/Spinc ontrol Univ ersal /062- 0030-0020-0050 Laufzei t - ohne T emp @ 28\mod_1405320531525_68.docx @ 194509 @ 4 @ 1
→
6.3.2.5
Runtime
NOTE
Version 04/2007, Rev. 2.23 of 28/04/2022 • sb
Translation from the original operating manual, part no. 0700602
The centrifuge is ready for operation when the start key is illuminated.
•
Press the start key in order to start a centrifugation run.
•
Press the stop key in order to interrupt a centrifugation run.
The centrifugation run will be terminated prematurely.
•
Press the start key during a deceleration process in order to interrupt it
and to restart the centrifuge.
•
Turn the left function knob in order to select a field. The selected field
will be preceded by the indication "set", "run", or "save".
•
Press the left function knob. The indication ("set", "run", or "save")
flashes and the modification mode is active.
•
Turn the right function knob in order to modify the set value of the
selected field.
•
Press the fright unction knob again to confirm the input and to quit the
modification mode
•
If the input is not confirmed, the value will be automatically reset to the
last setting.
The runtime is displayed in the left section of the display and can be set at
different intervals in a range from 10 seconds to 11 hours and 59 minutes.
The parameter runtime can be changed during the centrifugation.
If the runtime is changed during an active centrifugation run, the time that
has already elapsed will not be taken into consideration. The centrifuge
will perform a complete run with the new runtime.
Fig. 11: Setting the runtime
Laboratory Centrifuge Sigma 2-16P
6 Using the centrifuge
37 / 76
Advertisement
Table of Contents
