Safety Devices; Lid Lock Device; Standstill Monitoring System; System Check - Sigma 2-16KL Operating Manual

Refrigerated Centrifuge Sigma 2-16KL
3 Safety
→ Pos : 59 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070 Sic herheits einric htung en----------------------------------------- @ 27\mod_1405319034809_68.doc x @ 192157 @ 2 @ 1
3.7

Safety devices

→ Pos : 60 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070-0010 D eck elverri egelung @ 27\m od_1405319036321_68.docx @ 192171 @ 3 @ 1
3.7.1

Lid lock device

Pos : 61 /010 U nivers almodule/ Leerz eile 8pt @ 12 \mod_1337063062114_0.docx @ 65687 @ @ 1
Pos : 62 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070-0020 Stillstands überw achung @ 27\mod_1405319037803_68.docx @ 192185 @ 3 @ 1
→
3.7.2

Standstill monitoring system

Pos : 63 /010 U nivers almodule/ Leerz eile 8pt @ 12 \mod_1337063062114_0.docx @ 65687 @ @ 1
Pos : 64 /100 Sigma/100 BA Zentrifugen Sigma (S tandar dmodule)/030 Sic her heit/030-0070-0031 Systemk ontroll e Spincontr ol L @ 27\m od_1405319040423_68.docx @ 192213 @ 3 @ 1
→
3.7.3

System check

Pos : 65 /010 U nivers almodule/ Leerz eile 8pt @ 12\mod_1337063062114_0.docx @ 65687 @ @ 1
Pos : 66 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070-0041 Sc hutzleiterpr üfung ohne Potenti alausgleic hssc hraube @ 27\m od_1405319044593_68.docx @ 192255 @ 3 @ 1
3.7.4

Earth conductor check

Pos : 67 /010 U nivers almodule/ Leerz eile 8pt @ 12 \mod_1337063062114_0.docx @ 65687 @ @ 1
Pos : 68 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070-0051 U nw uchtüberwac hung Spi ncontr ol L+Easy+U nivers al @ 27\m od_1405319047031_68.docx @ 192283 @ 3 @ 1
→
3.7.5

Imbalance monitoring system

Pos : 69 /010 U nivers almodule/ Leerz eile 8pt @ 12 \mod_1337063062114_0.docx @ 65687 @ @ 1
Pos : 70 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070-0060 T emperatur überwac hung KL/KS/Z ent2 @ 27\m od_1405319048438_68.docx @ 192297 @ 3 @ 1
→
3.7.6

Temperature monitoring system

Pos : 71 /010 U nivers almodule/ Leerz eile 8pt @ 12 \mod_1337063062114_0.docx @ 65687 @ @ 1
Pos : 72 /100 Sigma/100 BA Zentrifugen Sigma (Standar dmodule)/030 Sic her heit/030-0070-0070 R otorüberwac hung @ 27\m od_1405319049932_68.docx @ 192311 @ 3 @ 1 →
3.7.7

Rotor monitoring system

Pos : 73 /010 U nivers almodule/ Seitenw ec hsel @ 0\m od_1202116244312_0.docx @ 105 @ @ 1
24 / 82
The centrifuge can only be started when the lid is properly closed. The
electrical lock must be locked. The lid can only be opened when the rotor
has stopped. If the lid is opened by way of the emergency release system
during operation, the centrifuge will immediately switch off and decelerate
brakeless. If the lid is open, the drive is completely separated from the
mains power supply, i.e. the centrifuge cannot be started (see chapter 7.1.1
- "Emergency lid release").
Opening of the centrifuge lid is only possible if the rotor is at a standstill.
This standstill is checked by the microprocessor.
An internal system check monitors the data transfer and sensor signals with
regard to plausibility. The system continuously performs a self-check and
identifies malfunctions. Error messages are displayed as "Error" followed
by a code number (see chapter 7.2 - "Table of error codes").
An earth conductor check can be carried out by authorised and specialised
personnel using a suitable measuring instrument. Please contact the Sigma
service department (see chapter 7.3 - "Service contact").
The indication "Imbalance" in the rotor field and, in some cases, also a
sound signal indicate that the centrifuge is in the impermissible imbalance
range.The drive will be switched off in the acceleration phase or during the
run.
If the temperature inside the rotor chamber rises above +50°C, the drive
system will be switched off automatically. The centrifuge cannot be
restarted until it has cooled.
When a rotor number and, if applicable, a bucket number are selected, the
computer will automatically check whether the entered speed or the
entered gravitational field are permissible for the selected rotor.
Translation of the original operating manual, part no. 0700702
Version 08/2012, Rev. 1.24 of 28/04/2022 • sb