SamplexPower EVO-RC-PLUS Owner's Manual page 104

Remote control for evolution series inverter/ charger
Table of Contents

Advertisement

SECTION 4 |
Parameter "BUZZER" provides option to switch on/ switch off the buzzer. The default option is "1=On".
4.8.2.7.1 Programming Steps for Parameter "BUZZER"
Any Operating Mode Screen from
Fig 3.1 to 3.8
E V O - 1 2 1 2 F
I n v e r t i n g
A C
o u t p u t :
1 2 0 . 0 V
< 0 . 1 0 A
6 0 . 0 0 H z
[Above screen is Screen 1 of Fig 3.2(a)]
4.8.2.8 DISCHARGE BEEP
(Table 4.9, (i) Parameter Setup Screen No. 7 under Column 1 (ii) Parameter Setup Screen No. 8 under Column 2)
When EVO™ Inverter/Charger is operating in "Inverting Mode", the batteries will be discharging. An audio alarm
buzzer has been provided inside the EVO™ Inverter/Charger that will provide pulsing beep once every 3 sec to signal
discharging of batteries under "Inverting Mode" (Refer to Table 6.1 in Section 6).
Parameter "DISCHARGE BEEP" provides option to switch on/ switch off this alarm signalling. The default option is "1=On".
NOTE: If parameter "BUZZER" (Section 4.8.2.7) is set for option "0=Off", the operation of the buzzer will be switched
off and there will be no discharge beeping even if parameter "DISCHARGE BEEP" has been set for option "1=On".
4.8.2.8.1 Programming Steps for Parameter "DISCHARGE BEEP"
Any Operating Mode Screen from
Fig 3.1 to 3.8
E V O - 1 2 1 2 F
I n v e r t i n g
A C
o u t p u t :
1 2 0 . 0 V
< 0 . 1 0 A
6 0 . 0 0 H z
[Above screen is Screen 1 of Fig 3.2(a)]
4.8.2.9 DEFAULT RESET
(Table 4.9, (i) Parameter Setup Screen No. 8 under Column 1 (ii) Parameter Setup Screen No. 9 under Column 2)
This is to reset all of the parameters to the Default Values.
104 | SAMLEX AMERICA INC.
Parameter Setup
Enter Key
S e l e c t
G r o u p
*
C H A R G E
C U R V E
ð
S e l e c t
P a r a m e t e r
O T H E R
F U N C T I O N
*
B U Z Z E R
1 = O n
Enter Key
S e l e c t
G r o u p
*
C H A R G E
C U R V E
ð
S e l e c t
P a r a m e t e r
O T H E R
F U N C T I O N
*
B U Z Z E R
1 = O n
Down Key x 4 times
S e l e c t
P a r a m e t e r
*
O T H E R
F U N C T I O N
ð
Enter Key
P a s s w o r d
k e y
0 0 0 0
ð
Password 8052
See Section 4.3.1
Down Key x 4 times
S e l e c t
P a r a m e t e r
*
O T H E R
F U N C T I O N
ð
Enter Key
P a s s w o r d
k e y
0 0 0 0
ð
Password 8052
See Section 4.3.1
(i) Down Key x 5 times for EVO-1212F/1212F-
HW/1224F/1224F-HW
(ii) Down Key x 6 times for EVO-2212/2212E/301
2/3012E/2224/2224E/4024/4024E
Enter Key
& EVO-4248SP
S e l e c t
P a r a m e t e r
O T H E R
F U N C T I O N
ð
*
P O
E R
S A V I N G
W
0 = D i s a b l e
Enter Key
S e l e c t
P a r a m e t e r
i n
O T H E R
F U N C T I O N
ð
*
B U Z Z E R
1 = O n
For programming options, see Table 4.9:
• Screen No.6 (Column 1) for
EVO-1212F/1212F-HW/1224F/1224F-HW
• Screen No.7 (Column 2) for
EVO-2212/2212E/3012/3012E/2224/2224E/4024/
4024E & EVO-4248SP
(i) Down Key x 6 times for EVO-1212F/1212F-
HW/1224F/1224F-HW
(ii) Down Key x 7 times for EVO-2212/2212E/301
2/3012E/2224/2224E/4024/4024E
Enter Key
& EVO-4248SP
S e l e c t
P a r a m e t e r
O T H E R
F U N C T I O N
ð
*
P O
E R
S A V I N G
W
0 = D i s a b l e
Enter Key
i n
S e l e c t
P a r a m e t e r
O T H E R
F U N C T I O N
ð
*
B U Z Z E R
1 = O n
For programming options, see Table 4.9:
• Screen No.7 (Column 1) for
EVO-1212F/1212F-HW/1224F/1224F-HW
• Screen No.8 (Column 2) for
EVO-2212/2212E/3012/3012E/2224/2224E/
4024/4024E & EVO-4248SP
ð
ð

Advertisement

Table of Contents
loading

Table of Contents