MacDon M150 Assembly Instructions Manual page 32

(Key On / Engine Running or Not / Header Disengaged).
(Press PROGRAM and SELECT on CDM to enter programming mode).
L1 C x x x || T R A C T O R
L2 M x x x ||
Y
C x x x || S E T
L1
E
M x x x ||
S
L2
C x x x || K N I F E
L1
M x x x ||
L2
or
C x x x || D I S K
L1
M x x x ||
L2
C x x x || O V E R L O A D
L1
M x x x ||
L2
C x x x || H E A D E R
L1
M x x x ||
L2
M x x x ||
L2
C x x x || R E T U R N
L1
M x x x ||
L2
M x x x ||
L2
C x x x || D W A
L1
M x x x ||
L2
Y
L1
E
S
L2
C x x x || T I L T
L1
M x x x ||
L2
C x x x || D I S C
L1
M x x x ||
L2
C x x x || H E A D E R
L1
M x x x ||
L2
C x x x || H A Y
L1
M x x x ||
L2
C x x x || A U G E R
L1
M x x x ||
L2
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
M x x x ||
L2
C x x x || S E T
L1
M x x x ||
L2
Y
L1
E
S
L2
L1
L2
L1
L2
L1
L2
L1
L2
Form # 169018
UNLOADING AND ASSEMBLY
DETAILED PROGRAMMING INSTRUCTIONS
Programming Menu Flow Chart
S E T U P ?
N O / Y E S
K N I F E S P E E D ?
1 2 0 0 S P M
O V E R L O A D
1 0 0 0 S P M
O V E R L O A D
2 0 0 0 R P M
P R E S S U R E ?
4 0 0 0 P S I
I N D E X
R E E L & C O N V E Y O R
R E E L O N L Y
T O C U T
H E I G H T &
H E I G H T O N L Y
I N S T A L L E D ?
N O / Y E S
C x x x || S W A P
D W A
M x x x ||
C Y L I N S T A L L E D ?
N O / Y E S
B L K I N S T A L L E D ?
N O / Y E S
C U T W I D T H ?
2 0 . 5 F E E T
C O N D I T I O N E R ?
N O / Y E S
H D R R E E L
R P M / M P H
R P M / K P H
T I R E S I Z E ?
1 8 . 4 X 2 6 T U R F
1 8 . 4 X 2 6 B A R
2 3 . 1 X 2 6 T U R F
6 0 0 - 6 5 R 2 8
E N G I N E I S C
N O / Y E S
C x x x || P R E S S
M x x x || I S C
R P M
C x x x || P R E S S
M x x x || I S C
R P M
C x x x || P R E S S
M x x x || I S C
R P M
C x x x || P R E S S
M x x x || I S C
R P M
C x x x || E X I T
E N G I N E
M x x x ||
If "NO" then jump to:
C A B D I S P L A Y
Mxxx refers to being set for a Cummins engine
S P D ?
When the programming mode is entered the header ID will be
displayed on the top line of the CDM using the last 4 display
S P D ?
Pressing "SELECT" will go to the next line 1 (L1) menu
M O D E ?
selection. The turn signal "arrow" keys are used to change the
values. Pressing "PROGRAM" at any time will cancel the
programming mode / menus and return back to the main
M O D E ?
T I L T
T I L T
C O N T R O L S ?
N O / Y E S
Appears for M150 ONLY - If "NO" then jump to:
H E A D E R
H E A D E R
Use the "arrow" keys to set the header cut
width. The header ID appears at the RHS.
DRAPER HEADER ONLY. Default will be
flashing. Use "arrow" keys to select.
S P D
Pressing "SELECT" will go to the next line 1
(L1) menu selection. The turn signal "arrow"
keys are used to change the values.
R P M ?
S E T
H A Z A R D T O S E T
O F F
H A Z A R D T O S E T
2 0 0 0
H A Z A R D T O S E T
1 9 0 0
H A Z A R D T O S E T
1 8 0 0
I S C ?
N O / Y E S
30
S E T U P ?
Cxxx refers to the CDM software version installed
refers to being set for a CAT engine.
positions.
operating displays.
If "NO" then jump to:
C Y L I N S T A L L E D ?
Swaps the GSL reel fore / aft with the DWA console
controls. If NO jump to DWA AUTO UP & DOWN?
C U T W I D T H ?
If "NO" then jump to:
C U T W I D T H ?
AUGER HEADER ONLY
For IMPERIAL display.
For METRIC display.
If "NO" then jump to:
C O N T R O L L O C K S ?
This is used to set the Intermediate Speed
Control function for the engine. The default or
last selected rpm will be displayed first and will
be flashing.
The "arrow" keys are used to cycle between the
selections. When "SELECT" is pressed the
program goes to the EXIT ENGINE ISC? menu
selection.
If "NO" then jump to:
P R E S S H A Z A R D
(continued next page)
Txxx
T O S E T
Model Year - 2009