Panasonic AJ-PG50EJ Operating Instructions Manual page 77

4
The server screen appears.
The folders on the set server are displayed. Use the cursor
buttons to select the transfer destination folder.
Note:
• Folder names using multi-byte characters are not displayed
correctly.
• Press the [TC PRESET] button to add a new folder to the current
folder list. (This operation is not related to the cursor position.)
Numeric characters indicating the date and time are auto-
matically entered for the name of the new folder but you can
set a different name with the full keyboard.
Note that some characters are not allowed on some FTP
servers.
A folder with the same name as an existing folder cannot be
created.
5
Align the cursor with "YES" and press the [SET] button.
Copying begins.
(➝ When importing on a clip basis, also refer to "Copying
Clips" page 48.)
When copying is completed, "COPY COMPLETED!" appears.
Note:
• Depending on the number of clips on the server and network
conditions, it may take some time to display thumbnails or
copy them.
• To stop copying, press the [SET] button, align the cursor
with "YES" in the CANCEL confirmation message, and press
the [SET] button. If the network is not disconnected, the par-
tially copied clips at the copy destination are deleted. If the
network is disconnected, incomplete clips may remain on
the FTP server.
• After copying starts, disconnection errors will no longer be
detected. Use the procedure above to stop a copy opera-
tion that has stalled.
• Confirm the amount of free space on the FTP server from
your FTP server administrator in advance because it cannot
be checked automatically before copying starts.
• Whether an error occurs when the remaining free space on the
FTP server reaches 0 depends on the FTP server. If an error is
not generated, use the procedure above to stop the operation.
• Clips cannot be copied to an FTP server folder that contains
more than 1000 clips.
• To use SSH, the FTP server must be SSH compliant.
• Setting SSH to "ENABLE" will reduce the transfer speed.
• Before you can check the result of a transfer on a computer
or other device, you may need to refresh the display on the
computer or other device.
• If a file that exceeds 4 GB was recorded with the "FILE
SPLIT" (➝ page 98) menu item set to "ONE FILE," that file
cannot be copied.
Writing back from an FTP server (copy)
Selected clips can be written back from an FTP server on the
network to a P2 card or hard disk.
1
Open the FTP thumbnail screen.
2
Select the clip to copy from the displayed thumbnails
on the server.
3
Press the [MENU] button to display the menu.
(➝ "Menu Operations" page 89)
4
Use the cursor buttons to align the cursor with the
"CLIP" - "COPY" (➝ page 93) menu item and press
the [SET] button.
5
Select the transfer destination (P2 slot or hard disk)
from the menu list and start writing back the data.
Note:
• Depending on the number of clips on the server and network
conditions, it may take some time to display thumbnails or
copy them.
• To stop copying, press the [SET] button, align the cursor
with "YES" in the CANCEL confirmation message, and press
the [SET] button. Partially copied clips at the copy destina-
tion are deleted.
• After copying starts, disconnection errors will no longer be
detected. Use the procedure above to stop a copy opera-
tion that has stalled.
• Clips cannot be copied to a P2 card or hard disk folder that
contains more than 1000 clips.
• To use SSH, the FTP server must be SSH compliant.
• Setting SSH to "ENABLE" will reduce the transfer speed.
• After an error occurs during an operation such as copying,
the connection to the FTP server may be disconnected, re-
sulting in the operation no longer being able to be contin-
ued. Should this happen, return to the FTP EXPLORE
screen, display the FTP thumbnail screen again, and then
restart the copying or other operation.
When copying is completed, "COPY COMPLETED!" ap-
pears.
Main Mode: Using the Unit Connected to a Network
77