AJA Ki Pro Ultra 12G Installation And Operation Manual page 51

IMPORTANT: If in Single Channel Mode a 6G or 12G signal is present on the
SDI 1 YCbCr (default)
SDI 1 RGB
SDI 1-2 YCbCr
SDI 1-2 RGB
SDI 1-4 YCbCr
SDI 1-4 RGB
Fiber 1 YCbCr
Fiber 1 RGB
Fiber 1-2 YCbCr
Fiber 1-2 RGB
Fiber 1-4 YCbCr
Fiber 1-4 RGB
HDMI
NOTE: If SDI is selected and a 6G or 12G signal is present on SDI 1, or if Fiber is selected
NOTE: Choosing the correct video input is a key component of successfully using the AJA
2. 1 0 Audio Input 1
(Multi Channel Mode only.) This parameter selects an audio input source for
Channel 1 from the audio input connections available, including embedded SDI
audio (which requires an SDI video source), AES, or analog audio (via the DB-25
connections).
AES (1-8)
SDI/Fiber (default)
Analog 1-8
AES (1/2 thru 7/8)
Analog (1/2 thru 7/8)
2. 1 1- 2. 1 3 Audio Input 2-4
(Multi Channel Mode only.) Selects the audio input for channels 2-4 (see above).
2. 1 5 3G Image Division Input
(Single Channel Mode only.) This parameter is used to select between Square
Division or Two Sample Interleave input format (4K and UltraHD signals only).
Ki Pro Ultra 12G can be set to use VPID to determine the input format. However,
external equipment does not always report the correct VPID. Therefore, it may be
necessary to force the input to Square Division or 2SI. Menu options are:
Ki Pro Ultra 12G File Based Recorder/Player v1.0
Ki Pro Ultra 12G's SDI 1 or Fiber 1 input, Ki Pro Ultra 12G will automatically
configure itself to support the 6G/12G input signal. In this case SDI/Fiber inputs
2-4 will be disabled, and user settings made in this menu will be ignored.
and a 6G or 12G signal is present on Fiber 1, the system will be configured to
support the 6G/12G signal. In this case SDI/Fiber inputs 2-4 will be disabled.
Ki Pro Ultra 12G. Be sure to determine the correct signal type being provided by
your camera or video source before configuring the 2.1 Video Input selection; if
an incorrect selection is made, unexpected or undesirable recordings may result.
If you are unsure of your signal type, you may use the built-in confidence monitor
and the Status menu to help determine the correct selection.
Selects all eight AES digital audio input pairs from the DB-25 AES
input connector
Selects all SDI embedded audio from the SDI or Fiber input
connector (if SDI video input is selected)
Selects all eight analog audio inputs from the DB-25 analog input
connector
Selects this AES input audio input pair
Selects this analog input audio pair
Sets SDI 1 to YCbCr input
Sets SDI 1 to RGB input
Sets SDI 1-2 to YCbCr input
Sets SDI 1-2 to RGB input
Sets SDI 1-4 to YCbCr input
Sets SDI 1-4 to RGB input
Enables 12G signal input and sets Fiber 1 to YCbCr input
Enables 12G signal input and sets Fiber 1 to RGB input
Sets Fiber 1-2 to YCbCr input
Sets Fiber 1-2 to RGB input
Sets Fiber 1-4 to YCbCr input
Sets Fiber 1-4 to RGB input
Sets input to HDMI connector
51 www.aja.com