AUMA SAVEx 07.2 Operation Instructions Manual page 90

Spare parts
Please state device type and our order number (see name plate) when ordering spare parts. Only original AUMA spare parts should be used.
Failure to use original spare parts voids the warranty and exempts AUMA from any liability. Representation of spare parts may slightly vary
from actual delivery.
Ref. no. Designation
002.0 Bearing flange
003.0 Hollow shaft
005.0 Drive shaft
005.1 Motor coupling
005.3 Manual drive coupling
006.0 Worm wheel
009.0 Manual gearing
017.0 Torque lever
018.0 Gear segment
019.0 Crown wheel
022.0 Drive pinion II for torque switching
023.0 Output drive wheel for limit switching
024.0 Drive wheel for limit switching
025.0 Locking plate
058.0 Cable for protective earth
070.0 Motor (only for V... motors incl. ref. no.
079.0)
079.0 Planetary gearing for motor drive (only for
V... motors)
155.0 Reduction gearing
500.0 Cover
502.0 Pin carrier without pins
505.0 Pin for controls
506.0 Pin for motor
511.0 Threaded plug
514.0 Output drive type A (without stem nut)
514.1 Axial needle roller bearing
514.2 Radial seal for output drive type A
516.0 Output drive type D
516.1 Output drive shaft D
535.1 Snap ring
539.0 Screw plug
541.0 Protective earthing
542.0 Handwheel with ball handle
549.0 Output drive types (B/B1/B2/B3/B4/C/E)
90
SAVEx 07.2 SAVEx16.2/SARVEx 07.2
Type
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
SARVEx16.2 Control unit: electronic (MWG)
Ref. no. Designation
549.1 Output drive sleeve (B/B1/B2/B3/B4/C/E)
551.1 Parallel key
553.0 Mechanical position indicator
554.0 Socket carrier for motor plug/socket con-
nector with cable harness
556.0 Potentiometer as position transmitter
556.1 Potentiometer without slip clutch
557.0 Heater
558.0 Blinker transmitter including pins at wires
(without impulse disc and insulation plate)
559.0 1 Electromechanical control unit with
switches, including torque switching heads
559.0 2 Electronic control unit with magnetic limit
and torque transmitter (MWG)
560.0 1 Switch stack for direction OPEN
560.0 2 Switch stack for direction CLOSE
560.1 Switch for limit/torque
560.2 1 Switch case for direction OPEN
560.2 2 Switch case for direction CLOSE
566.0 RWG position transmitter
566.1 Potentiometer for RWG without slip clutch
566.2 Position transmitter board for RWG
566.3 Cable set for RWG
567.1 Slip clutch for potentiometer
568.1 Stem protection tube (without cap)
568.2 Protective cap for stem protection tube
568.3 V-seal
568.4 Threaded sleeve
575.1 Stem nut for output drive type A
583.0 Motor coupling on motor shaft
583.1 Pin for motor coupling
584.0 Retaining spring for motor coupling
614.0 EWG position transmitter
627.0 MWG 05.03 cover
628.0 Ex plug/socket connector with terminal
connection (KT)
S1 Seal kit, small
S2 Seal kit, large
ACVExC 01.2 Non-Intrusive
Type
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Set
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Set
Set