Komatsu D37EX-24 Operation & Maintenance Manual page 366

If machine monitor shows warning display......... 3-218
Indicator - Check electrolyte level......................... 4-42
Inducement Strategy for abnormalities recurrences
within 40 hours............................................. 3-118
Inducement strategy when abnormalities are detected
in the Urea SCR System devices Except abnor-
malities in the EGR system.......................... 3-111
Inducement strategy when abnormality is found in the
EGR Valve System by the Urea SCR system.......
..................................................................... 3-113
Inducement strategy when the DEF tank Level be-
comes low....................................................3-108
Inside operator's compartment............................. 2-12
Inspecting machine............................................... 2-11
Introduction............................................................. 1-8
Investigate and confirm jobsite conditions............ 2-18
Joystick (steering, directional and gear shift lever)
(PCCS lever)..................................................3-90
Jumper cable - Connect......................................3-213
Jumper cable - Disconnect................................. 3-213
KCCV filter element - Replace.............................. 4-62
Keep machine clean..............................................2-11
Komatsu Closed Crankcase Ventilation (KCCV) 3-102
Komatsu genuine lubricants....................................4-2
Komatsu genuine replacement parts...................... 4-2
KOMTRAX.......................................................... 3-119
Lamp - Check operation......................................3-133
Language - Set..................................................... 3-75
Leveling work...................................................... 3-175
Lifting of personnel prohibited...............................2-15
Link pitch - Measure............................................3-179
Load display..........................................................3-41
Loading and unloading with trailer...................... 3-196
Location of engine serial No. plate........................1-12
Location of product identification number (PIN) / ma-
chine serial No. plate..................................... 1-12
Location of safety labels......................................... 2-5
Lock.................................................................... 3-182
Lock inspection cover............................................. 4-3
Low register range (bass) - Adjust...................... 3-194
Lubrication chart..................................................... 7-5
Lumber support - Adjust................. 3-138,3-141,3-143
Lunch box fixing belt............................................. 3-94
Machine - Check walk-around............................ 3-121
Machine - Clean inside......................................... 4-21
Machine - Lift...................................................... 3-201
Machine - Load................................................... 3-196
8-4
J
K
L
M
Machine - Lubricate.............................................. 4-38
Machine - Operate.............................................. 3-177
Machine - Park....................................................3-180
Machine - Running-in the new machine..............3-155
Machine - Secure................................................3-197
Machine - Set each item / Save memory.............. 3-44
Machine - Shift gear............................................3-163
Machine - Start....................................................3-160
Machine - Start (Travel forward and reverse) / Stop....
.....................................................................3-160
Machine - Start after long-term storage.............. 3-205
Machine - Steer...................................................3-167
Machine - Stop....................................................3-162
Machine - Switch travel direction........................ 3-166
Machine - Transport............................................ 3-195
Machine - Travel on load.....................................3-195
Machine - Turn during forward travel.................. 3-168
Machine - Turn gradually during forward travel on
downhill slope.............................................. 3-170
Machine - Turn normally..................................... 3-167
Machine - Turn on downhill slope....................... 3-170
Machine - Unload................................................3-200
Machine equipment name.......................................3-2
Machine monitor - Basic operation when stopping en-
gine in normal situation....................................3-7
Machine monitor - Check.................................... 3-134
Machine monitor - Operate when operator identifica-
tion function is available with skip..................3-76
Machine monitor - Operate when operator identifica-
tion function is available without skip.............3-78
Machine monitor - Operate when starting engine in
abnormal situation........................................... 3-9
Machine monitor - Operate when starting engine in
normal situation............................................... 3-6
Machine monitor - Operate when starting engine
while engine shutdown secondary switch is ON...
.........................................................................3-6
Machine monitor - Operate when starting switch is
ON while operator ID input is set..................... 3-8
Machine monitor - Operate when trouble occurs while
operating machine......................................... 3-10
Machine monitor equipment name..........................3-4
Machine operations and controls........................ 3-121
Machine settings................................................... 3-62
Main use of machine...............................................1-8
Maintenance during long-term storage............... 3-205
Maintenance of air conditioner..............................2-35
Maintenance procedure........................................ 4-14
Maintenance schedule.......................................... 4-12
Maintenance schedule table................................. 4-12
Maintenance screen - Set..................................... 3-67
Maintenance time caution lamp............................ 3-24
Master link connecting bolt - Retighten.................4-25
Mechanical suspension seat...............................3-139
Memory - Call........................................................3-45
Message - Check.................................................. 3-79
Message - Reply................................................... 3-80
Message display........................................... 3-26,3-79
INDEX