00 Index and foreword
Foreword, safety and general information
Width
Nominal
across
No. of
flats
hose
(mm)
02
19
22
03
24
04
27
128 to 186 {13.0 to 19.0}
05
32
177 to 245 {18.0 to 25.0}
06
36
(10)
177 to 245 {18.0 to 25.0}
41
(12)
197 to 294 {20.0 to 30.0}
46
(14)
246 to 343 {25.0 to 35.0}
55
Table of tightening torque for face seal joints
a The tightening torque table below applies to the seal joint (sleeve nut type)
a The table is applied to the threads coated with engine oil (wet threads).
Outside
Width
diameter of
across flats
pipe (mm)
(mm)
8
19
10
22
24 {27}
12
15 {16}
30 {32}
22 {20}
36
Reference: The face seal joint of the dimension in ( ) is also used, depending on the specification.
Tightening torque table for bolts and nuts on 102,107 and 114 series engines
a Unless otherwise specified, tighten the metric threads bolts and nuts used on the 102, 107 and 114 series
engines to the torques shown in the table below.
Thread diameter (mm)
6
8
10
12
14
00-52
Tightening torque (Nm {kgm})
Range
34 to 54 {3.5 to 5.5}
34 to 63 {3.5 to 6.5}
54 to 93 {5.5 to 9.5}
59 to 98 {6.0 to 10.0}
84 to 132 {8.5 to 13.5}
Tightening torque (Nm {kgm})
Range
14 to 16 {1.4 to 1.6}
24 to 27 {2.4 to 2.7}
43 to 47 {4.4 to 4.8}
60 to 68 {6.1 to 6.8}
90 to 95 {9.2 to 9.7}
Taper seal
Thread size
Target
(mm)
44 {4.5}
44 {4.5}
14
74 {7.5}
78 {8.0}
18
103 {10.5}
22
157 {16.0}
24
216 {22.0}
30
216 {22.0}
33
245 {25.0}
36
294 {30.0}
42
Nominal No. -
Target
threads per inch,
type of thread
15 {1.5}
25.5 {2.6}
45 {4.6}
64 {6.5}
92.5 {9.4}
Tightening torque (Nm {kgm})
10 ± 2 {1.02 ± 0.20}
24 ± 4 {2.45 ± 0.41}
43 ± 6 {4.38 ± 0.61}
77 ± 12 {7.85 ± 1.22}
Face seal
Thread root
Nominal No. -
diameter
threads per
(mm)
inch, type of
(reference)
thread
/
-18UN
14.3
9
16
/
-16UN
17.5
11
16
13
/
-16UN
20.6
16
1 -14UNS
25.4
1
3
/
-12UN
30.2
16
Face seal
Thread root
diameter (mm)
(reference)
9
/
-18UN
14.3
16
11
/
-16UN
17.5
16
13
/
-16UN
20.6
16
1 -14UNS
25.4
1
3
/
-12UN
30.2
16
PC88MR-10