Table of Contents
Advertisement
Speed Loop Parameter Ratio (F379), 121
Speed Loop Proportional Gain (F376), 120
Speed Reach Detection Band (F102), 60
Speed Reach Frequency (F101), 60
ST, 17, 18
ST Signal Selection (F103), 61
ST1, 13
Stall Cooperation Gain at Field Weakening Zone
(F485), 136
Stall Prevention Level (F601), 143
Startup
and Test, 16
Wizard, 30
Wizard Requirements, 47
Stop Key, 26
Stop Pattern (F721), 156
SW1, 20
SW2, 20
System
Configuration, 32
Grounding, 14
Operation, 30
T
Terminal Descriptions, 18
Timer, 33
Torque, 33
Alarm Display (Boost), 179
Alarm Display (Torque Boost), 179
Boost Adjustment (F654), 151
Command Filter (F421), 126
Command Mode Selection (F429), 128
Command Selection (F420), 126
Current, 33
Heavy-Load Torque During Forward
Acceleration (F336), 114
Heavy-Load Torque During Forward
Deceleration (F337), 115
Heavy-Load Torque During Reverse
Acceleration (F339), 115
Heavy-Load Torque During Reverse
Deceleration (F340), 115
Limit Group (F723), 157
Limit Mode (F450), 132
Limit Mode (Speed Dependent) (F451), 132
Load Inertia (Acc/Dec Torque) (F325), 112
Load Torque Filter (F326), 112
Manual Torque Boost 1 (F016), 56
Manual Torque Boost 2 (F172), 75
Manual Torque Boost 3 (F176), 77
Over-Torque Detection Level During Power
Running (F616), 146
https://www.toshiba.com/tic/
W7B ASD Installation & Operation Manual
Over-Torque Detection Level During
Regenerative Braking (F617), 146
Over-Torque Detection Time (F618), 147
Over-Torque Trip Selection (F615), 146
Power Running Stall Continuous Trip Detection
Time (F452), 132
Power Running Torque Limit #1 (F440), 130
Power Running Torque Limit 2 Level
(F444), 130
Power Running Torque Limit 4 Level
(F448), 131
Reference, 33
Regeneration Torque Limit 1 (F442), 130
Regeneration Torque Limit 2 (F445), 131
Regeneration Torque Limit 3 (F447), 131
Regeneration Torque Limit 4 (F449), 131
Regeneration Torque Limit Setting 1
(F443), 130
Switching Load Torque During Forward-Run
(F335), 114
Switching Load Torque During Reverse Run
(F338), 115
Synchronized Torque Bias Input Selection
(F422), 126
Tension Torque Bias Input Selection
(F423), 127
Tension Torque Bias Input Selection (Torque
Control) (F423), 127
Trip
At-Trip Recorded Parameters, 186
Clearing a Trip, 186
History, 186
Record at Monitor Screen, 186
Trip, 177
Viewing Information, 186
Trip Display
CPU Error, 182
Ctrl EEPROM Err, 182
EEPROM Write Error, 182
Emergency Off, 182
Encoder Loss, 182
Flash Error, 182
In(put) Phase Loss, 182
Load End OC, 183
Option PCB Error, 184
Out(put) Phase Loss, 184
Overheat, 184
Over-Torque, 184
RAM Err, 184
ROM Err, 184
Sink/Source Error, 184
Speed Error, 184
Type(form) Error, 184
U Phase OC, 185
Under Curr(ent) Trip, 185
Index
209
Advertisement
Table of Contents
