1. Manuals
  2. Brands
  3. Graco Manuals
  4. Control Systems
  5. Horizon Fluid Management Systems
  6. Instructions manual

Change 110 Vac To 220 Vac - Graco Horizon Fluid Management Systems Instructions Manual

Hide thumbs
Table of Contents

Advertisement

3. Set Control Module Addresses and
Label the Boxes (continued)
DIP
1
2
3
Switch
No.
Setting
g
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
OFF
OFF
ON
ON
OFF
ON
OFF
ON
ON
ON
ON
ON
OFF
OFF
OFF
Hardware Installation
4
5
6
Address
OFF
OFF
OFF
0*
OFF
OFF
OFF
1
OFF
OFF
OFF
2
OFF
OFF
OFF
3
OFF
OFF
OFF
4
OFF
OFF
OFF
5
OFF
OFF
OFF
6
OFF
OFF
OFF
7
ON
OFF
OFF
8
ON
OFF
OFF
9
ON
OFF
OFF
10
ON
OFF
OFF
11
ON
OFF
OFF
12
ON
OFF
OFF
13
ON
OFF
OFF
14
ON
OFF
OFF
15
OFF
ON
OFF
16
OFF
ON
OFF
17
OFF
ON
OFF
18
OFF
ON
OFF
19
OFF
ON
OFF
20
OFF
ON
OFF
21
OFF
ON
OFF
22
OFF
ON
OFF
23
ON
ON
OFF
24
ON
ON
OFF
25
ON
ON
OFF
26
ON
ON
OFF
27
ON
ON
OFF
28
ON
ON
OFF
29
ON
ON
OFF
30
ON
ON
OFF
31
OFF
OFF
ON
32
OFF
OFF
ON
33
OFF
OFF
ON
34
OFF
OFF
ON
35
OFF
OFF
ON
36
OFF
OFF
ON
37
OFF
OFF
ON
38
OFF
OFF
ON
39
ON
OFF
ON
40
*
Slave Control Modules are shipped with their address set
to 0.
4. To Change from 110 VAC to 220 VAC
WARNING
FIRE, EXPLOSION, AND ELECTRIC
SHOCK HAZARD
To reduce the risk of fire, explosion, and
electric shock all wiring must be done by
a qualified electrician.
a. Power should not be connected at this point of
installation if the procedure is being followed
properly. Make sure there is no power to the
control module(s).
b. See Fig. 2 wire connections for 110 VAC. Cut
the white wire connecting transformer termi-
nals 2 to 6 at the terminal 2 connector.
c. Cut the black wire connecting transformer
terminals 1 to 5 at the terminal 1 connector.
d. Switch the connectors on terminals 2 and 6.
See Fig. 2 wire connections for 220 VAC.
e. Strip 0.25 in. (6.4 mm) of insulation from the
wires connected to terminals 2 and 5. Connect
the wires together with a wire nut.
308607
11

Advertisement

Table of Contents
loading

Related Manuals for Graco Horizon Fluid Management Systems

Related Products for Graco Horizon Fluid Management Systems

Table of Contents