Analog Devices ADSP-21479 EZ-Board Manual page 111

Index
shift register
interface, 1-18
interface connector (P4),
signal routing units
SRU2 (DPI interface),
SRU (DAI interface),
single-processor configuration, 2-16,
SPDIF_IN signal, 1-20,
S/PDIF interface
connections, 1-20, 2-3
in connector (J6), 1-20,
loopback jumper (JP2),
out connector (J7), 1-20,
SPDIF_OUT signal, 1-20,
SPI_CLK signal, 2-5, 2-9
SPI_CS signal, 2-5, 2-9
SPI interface, 1-16
SPI_MISO signal, 2-5,
SPI_MOSI signal, 2-5,
SPORT0-7 signals, 1-19
SRAM interface, 1-13,
SR_LAT signal, 1-18
SR_SCLK signal, 1-18
SR_SDI signal, 1-19
standalone debug agent, xi, 1-9, 1-12,
startup, of this EZ-Board
CCES, 1-5
stopwatch function, 1-18
SW12 (reset) push button,
SW13 (external port enable), 1-15, 1-17,
1-24, 2-6, 2-12
SW14 (DPI 9-14 enable) switch, 1-22, 2-5,
2-13
SW15 (audio left select) switch,
SW16-17 (audio right select) switches,
2-14, 2-15
SW18 (audio left select) switch,
SW19-22 (JTAG) switches, 1-25,
SW1 (DAI 1-8 enable) switch, 1-20, 2-3,
2-8
I-4
2-27
2-4
2-3
2-17
2-11
2-25
2-20
2-25
2-8
2-9
2-9
1-15
1-24
2-12
2-14
2-16
2-16
ADSP-21479 EZ-Board Evaluation System Manual
SW23 (headphone enable) switch, 1-22,
2-18
SW24-25 (audio loopback) switches,
SW2 (DAI 9-16 enable) switch,
SW3 (DPI 1-8 enable) switch, 1-16, 2-5,
2-9
SW4 (boot mode select) switch, 1-16,
SW5 (DSP clock config),
SW7 (DAI 17-20 enable) switch, 1-20,
1-24, 2-11, 2-12
SW8-11 (IO) push buttons, 1-24,
switches, diagram of locations,
system architecture, of this EZ-Board,
T
technical support, xvi
time-division multiplexed (TDM) mode,
1-21
U
UART
interface connections,
loopback jumper (JP4),
RTS/CTS jumper (JP3),
UART_CTS signal, 1-22, 2-5, 2-13,
UART_RTS signal, 1-22, 2-5, 2-13,
UART_RX signal, 1-22, 2-5,
UART_TX signal, 1-22, 2-5,
universal asynchronous receiver
transmitter, See UART
USB monitor LED (LED4),
V
VDDEXT
power connector (P6),
voltage domain, 1-27
2-18
2-8
2-10
2-10
2-12
2-7
2-2
1-22
2-20
2-20
2-20
2-20
2-13
2-13
1-9
2-28