JLG TOUCAN 10E Service And Maintenance Manual page 133

DTC FAULT MESSAGE
SLAVE MODULE RAM FAIL-
99107
URE
MASTER MODULE - INTER-
99108
NAL ERROR
SLAVE MODULE - INTERNAL
99109
ERROR
MASTER MODULE - INTER-
99110
NAL ERROR
SLAVE MODULE - INTERNAL
99111
ERROR
MASTER MODULE - INTER-
99112
NAL ERROR
MASTER MODULE - INTER-
99114
NAL ERROR
SLAVE MODULE - INTERNAL
99115
ERROR
MASTER MODULE - INTER-
99116
NAL ERROR
SLAVE MODULE - INTERNAL
99117
ERROR
MASTER MODULE - INTER-
99118
NAL ERROR
SLAVE MODULE - INTERNAL
99119
ERROR
MASTER MODULE - INTER-
99120
NAL ERROR
SLAVE MODULE - INTERNAL
99121
ERROR
MASTER MODULE - INTER-
99122
NAL ERROR
SLAVE MODULE - INTERNAL
99123
ERROR
31210090
DESCRIPTION
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
There is an internal error in the Master
Module (right controller).
There is an internal error in the Slave Mod-
ule (left controller).
– JLG Lift –
SECTION 10 - DIAGNOSTIC TROUBLE CODES
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Master con-
troller.
• Cycle power to clear the fault.
• If the fault is not cleared : Replace the Slave control-
ler.
CHECK
10-21