Table of Contents

Advertisement

Quick Links

O W N E R ' S
M A N U A L

Advertisement

Table of Contents
loading

Summary of Contents for Tiffin Motorhomes VANLEIGH BEACON

  • Page 1 O W N E R ’ S M A N U A L...
  • Page 2: Table Of Contents

    T A B L E O F C O N T E N T S Introduction About This Manual Contact Information Owner Information Package Manufacturing Certification The Vehicle Identification Number Safety Precautions Safety Messages Additional Terminology Used Reporting Safety Defects To Contact the NHTS Toll-Free Vehicle Safety Hotline Service and Warranty...
  • Page 3 Ta ble of Co n T en T s Smoke Alarm Carbon Monoxide (CO) CO/LP Gas Alarm Indoor Air Quality Chemical Sensitivity & Offgassing Formaldehyde Effects Of Prolonged Occupancy Where There Is Moisture, There May Be Mold Cold Weather Use Pre-Travel Information Additional Safety Precautions Towing...
  • Page 4 Ta ble of Co n T en T s Tire Ply Composition & Materials Tire Safety Tips Tire Maintenance Tire Balance and Wheel Alignment Tire Rotation Tire Repair Tire Tread Tire Pressure Checking Tire Pressure How Overloading Affects Your RV and Tires Trailer Tire Labeling Us Dot Tire Identification Number (TIN) Maximum Load Rating...
  • Page 5 Ta ble of Co n T en T s 12-Volt DC System 12- Volt Fuse Panel Batteries Battery Vent Battery Disconnect Battery Inspection and Care Spyder Control System Calculating Electrical Load Solar Port Approximate Electrical Load Ratings Plumbing Systems Fresh Water System — First Use Plumbing functions within the Spyder Controls 12V Water Pump Fresh Water Holding Tank...
  • Page 6 Ta ble of Co n T en T s Winterization Water Heater Draining and Winterization Winterizing Dewinterizing Propane System Propane Gas Propane Gas Cylinders Propane Leak Test Propane Alarm Installing The Propane Cylinders Propane Regulator LP Distribution System Recommended Practices Propane System Hoses, Tubes, Pipes &...
  • Page 7 Ta ble of Co n T en T s TV Roof Antenna Cable/Satellite Outlet Satellite Prep Heating & cooling Ducting & Return Air Roof Vent/Fans Thermostat Furnace Heat Pump Air Conditioning Fireplace Slideout Systems Slideout Operation Hydraulic Slide-Out Manual Override Schwintek In-Wall Slideout System Manual Override Troubleshooting The Schwintek In-Wall Slide System Exterior Features...
  • Page 8 Ta ble of Co n T en T s Decor Items Kitchen Sink Bathroom Sink, Shower, & Accessories Stainless Steel Sink & Appliances Exterior care Cleaning the Exterior Exterior Roof Sidewall Vents Windows Doors Trailer Frame Sealant RV Storage Winter Storage Suggested Maintenance Checklist Basic Troubleshooting Air Conditioner (Roof)
  • Page 9 Ta ble of Co n T en T s Water Heater Water Pump Water System Maintenance Data and charts RV Owner’s Data Sheet RV Owner’s Maintenance Record Glossary VA N L E I G H B E A c o N...
  • Page 10 L I S T O F F I G U R E S Figure 1. Manufacturing Certification Placard Figure 2. VIN Number Figure 3. Fire Extinguisher Figure 4. Emergency Egress Window Figure 5. Smoke Alarm Figure 6. Propane/CO Alarm Figure 7. CARB Notice Label Figure 8.
  • Page 11 l isT of figur es Figure 33. Spyder Control Unit Figure 34. Spyder Lights Screen Figure 35. Spyder Dimming Control Screen Figure 36. Solar Port Figure 37. Sanitize the Water Tank before First Use Figure 38. Spyder Control Unit Figure 39. Water Pump Figure 40.
  • Page 12 l isT of figur es Figure 67. Black Tank Flush Line Figure 68. Gate Valve Figure 69. Low-Point Drains located under the RV Figure 70. Water Pump Switch Figure 71. Water Heater Drain Figure 72. Ice Maker Valve in Wet Bay Figure 73.
  • Page 13 l isT of figur es Figure 101. Roof Vent Fan Figure 102. Spyder Controls - Fans Figure 103. Bathroom Fan Touchpad Controls Figure 104. Spyder Controls—Climate Figure 105. Temperature Sensor Figure 106. Furnace Figure 107. Furnace Ductwork Figure 108. Furnace Discharge—Galley Figure 109.
  • Page 14 l isT of figur es Figure 135. Recliner/Sofa Controls Figure 136. Shades Figure 137. Exterior Appliance Doors Figure 138. Windows Figure 139. Front Door Figure 140. Trailer Frame Figure 141. Roof Sealant Figure 142. 10A Fuse and Resettable Breakers for Jacks/Leveling System Figure 143.
  • Page 15 L I S T O F T A B L E S Table 1. VIN Numbers Table 2. Component Supplier Contact Information Table 3. Component Manufacturers Limited Warranty Information Table 4. Fire Extinguisher Types Table 5. Trailer Axle Maintenance Schedule Table 6. Brake Controller Compatibility Table 7. Tire Wear Patterns Table 8.
  • Page 16: Introduction

    I N T R O D U C T I O N A B o U T T H I S M A N U A L The objective of this manual is to provide a guide for normal operations, safety, care, and maintenance of your recreation vehicle (RV).
  • Page 17: Manufacturing Certification

    i n T rod u C T ion • It is crucial that you register and submit each warranty card within the time limit provid- ed to avoid loss of warranty coverage. • Some component manufacturers present warranties beyond the Vanleigh RV Limited Base and Structural Warranties.
  • Page 18: Figure 2. Vin Number

    i n T rod u C T ion Figure 2. VIN Number Table 1. VIN Numbers Vin position Description Code Code Name 1 Through 3 Type of Trailer/ Vanleigh RV Fifth Wheel Make Body Type Beacon Vanleigh RV/Fifth Wheel Pinecrest Vilano 6 Through 7 Length 32 Feet...
  • Page 19: Safety Precautions

    i n T rod u C T ion S A F E T Y P R E C A U T I O N S There is nothing more essential than the individual safety of you, your family and others. Safety includes several areas of the RV experience.
  • Page 20 i n T rod u C T ion [If so equipped] This includes items that may be installed by Vanleigh RV on certain RVs. Although, some items listed as “if so equipped” can only be incorporated during the manu- facturing stage and cannot be added at another time. The involvement of items listed as “if so equipped”...
  • Page 21: Reporting Safety Defects

    R E P O R T I N G S A F E T Y D E F E C T S IN THE UNITED STATES If you believe your vehicle has a deficiency, that might cause an accident, injury or death, we encourage you to immediately contact the National Highway Traffic Safety Administra- tion (NHTSA) and Vanleigh RV.
  • Page 22: Service And Warranty

    S E R V I C E A N D W A R R A N T Y DEALER’S RESP oNSIBILITIES When you buy your new RV, at the time of purchase, your dealer is expected to: Deliver your RV in the best condition possible. Your RV must pass the dealer’s Pre-Delivery Inspection (PDI).
  • Page 23: Obtaining Warranty Service

    s erViCe a n d Wa r ran T Y With your other personal belongings, it is crucial to secure yourself and others with insur- ance coverage. Your insurance agent can aid you in receiving the appropriate insurance coverage for personal liability collision, property damage, theft, liability, etc. O B T A I N I N G W A R R A N T Y S E R V I C E WARRANTY SERVICE Warranty service must be obtained:...
  • Page 24: Obtaining Emergency Warranty Repair

    s erViCe a n d Wa r ran T Y • If a problem re-occurs after leaving the dealership, contact the dealer’s service manager and Vanleigh RV Customer Support to quickly resolve the issue. O B T A I N I N G E M E R G E N C Y W A R R A N T Y R E P A I R A roadside emergency can happen at any time, whether your RV is new or old.
  • Page 25 s erViCe a n d Wa r ran T Y clude your name, address, phone number, RV 17-digit VIN and authorization number. If returning parts, include a copy of your freight bill. Inspect the completed repair work thoroughly. If you are not satisfied, communicate that to the RV repair facility management.
  • Page 26: Updating Your Contact Information

    s erViCe a n d Wa r ran T Y U P D A T I N G Y O U R C O N T A C T I N F O R M A T I O N Federal law requires that we keep a record of all Vanleigh RV owners.
  • Page 27: One Year Limited Base Warranty

    s erViCe a n d Wa r ran T Y VANLEIGH RV O N E Y E A R L I M I T E D B A S E W A R R A N T Y SUMMARY What does this Warranty cover? Vanleigh RV, Inc.
  • Page 28 s erViCe a n d Wa r ran T Y should have been discovered by a reasonable person exercising reasonable care according to the terms of this Limited Warranty. The person seeking the replacement of the defective part or labor must be the orig- inal retail consumer purchaser.
  • Page 29 s erViCe a n d Wa r ran T Y Routine maintenance and adjustments; Consequential/incidental expenses (damages) such as service calls, transportation, lodging, food, fuel, etc. Fading, yellowing or aging of exterior materials due to UV or sunlight or weather ex- posure;...
  • Page 30 s erViCe a n d Wa r ran T Y WARRANToR’S oBLIGATIoNS — HoW To GET WARRANTY SERVIcES How Do You Get Service? In no event shall repair or replacement for a defect be covered under this Warranty unless the repair or replacement occurs at Warrantor’s facilities, or Warrantor’s designated repair shop or dealer.
  • Page 31 s erViCe a n d Wa r ran T Y hicle serial number (VIN), date of purchase, and a description of the issue or concern. If you cannot locate a dealer, please go to the Warrantor’s web site or contact Warrantor directly for immediate assistance.
  • Page 32 s erViCe a n d Wa r ran T Y TO THE EXTENT NOT EXCLUDED IN THIS LIMITED WARRANTY, THE IMPLIED WARRAN- TY OF MERCHANTABILITY, AN UNWRITTEN WARRANTY THAT THE PRODUCT IS FIT FOR ORDINARY USE, IS LIMITED TO THE WARRANTY PERIOD OF THIS WRITTEN WARRANTY, AND ANY OTHER IMPLIED WARRANTY ARISING BY OPERATION OF LAW ARE SPECIF- ICALLY LIMITED TO THE WARRANTY PERIOD OF THIS WRITTEN WARRANTY TO THE EXTENT NOT ACTUALLY EXCLUDED IN THIS LIMITED WARRANTY.
  • Page 33: Three Year Limited Structural Warranty

    s erViCe a n d Wa r ran T Y or nature, shall entitle Warrantor to recover its costs, damages, and reasonable attorney’s fees in connection with the same. How Does State Law Relate to This Warranty? This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
  • Page 34 s erViCe a n d Wa r ran T Y WARRANTIES BEYOND THOSE SET FORTH HEREIN. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN ADDITION TO THE EX- CLUSIONS SET FORTH IN THIS LIMITED WARRANTY, THIS WARRANTY DOES NOT APPLY TO DAMAGE DUE TO NEGLIGENT USE, MISUSE, ABUSE OR ACCIDENT INVOLVING ANY PART AND/OR ALL OF THE STRUCTURAL COMPONENTS, OR THE REPAIR OR ALTER- ATION OF SUCH STRUCTURAL COMPONENTS.
  • Page 35 s erViCe a n d Wa r ran T Y Neglect of the recreational vehicle or STRUCTURAL COMPONENTS; Repairs or replacements made necessary by reason of a failure of the original retail consumer purchaser or others to follow ordinary maintenance procedures as recom- mended by the Warrantor or the manufacturer or dealer of the Structural Compo- nents;...
  • Page 36 s erViCe a n d Wa r ran T Y Damage caused by overloading or improper weight distribution; Damage caused by improper ventilation resulting in excessive condensation which results in water damage and/or mold or mildew; Damage, fading or deterioration caused by prolonged exposure to natural elements; Damage caused by infestation by insects or other animals;...
  • Page 37 s erViCe a n d Wa r ran T Y NENTS ONLY of the recreational vehicle. Warranty performance can only be obtained at Warrantor’s authorized dealers and service representatives. All costs incurred in transport- ing this recreational vehicle for warranty service shall be borne by purchaser unless other- wise approved in advance by Warrantor.
  • Page 38 s erViCe a n d Wa r ran T Y DIScLAIMER oF coNSEQUENTIAL, PUNITIVE AND INcIDENTAL DAMAGES What other conditions or limitations apply to this Warranty? The original retail purchaser of the recreational vehicle and any person to whom the rec- reational vehicle is transferred or given or conveyed, and any person who is an intended or unintended user or beneficiary of this Limited Warranty, shall not be entitled to recov- er from Warrantor any consequential, punitive or incidental damages resulting from any...
  • Page 39 s erViCe a n d Wa r ran T Y WILL NOT BE EFFECTIVE. NO PERSON HAS THE AUTHORITY TO ENLARGE, AMEND, OR MODIFY THIS WARRANTY. DESIGN cHANGES Warrantor reserves the right to change the design of its STRUCTURAL COMPONENTS from time to time without notice and without obligation to make corresponding changes in its products previously manufactured.
  • Page 40: Component Supplier Contact Information

    s erViCe a n d Wa r ran T Y C O M P O N E N T S U P P L I E R C O N TA C T I N F O R M AT I O N All component suppliers listed are correct at the time of publication.
  • Page 41: Component Manufacturer Warranty Information

    s erViCe a n d Wa r ran T Y Component brand supplier Website Phone number Tires and Wheels Westlake from Lions- www.lionsheadtireandwheel.com (574) 533-6169 head Tire & Wheel Toilets Dometic www.dometic.com (800) 544-4881 Thetford www.thetford.com (800) 543-1219 TV Antenna King www.kingconnect.com (303) 772-9591...
  • Page 42 s erViCe a n d Wa r ran T Y Component brand Manufacturer Warranty Frame Lippert Components Three year warranty from date of purchase. Original owner only. Furnace Suburban Two year limited warranty. Inverter 1000W Sensata Tech One year limited warranty. Leveling System Lippert Components One year warranty from date of purchase.
  • Page 43 s erViCe a n d Wa r ran T Y Component brand Manufacturer Warranty Water Heater Atwood Two year limited warranty from date of purchase. Original owner only. Truma 12 month year limited warranty from date of purchase. Register your water heater to receive an additional 12 months.
  • Page 44: Occupant Safety

    O C C U P A N T S A F E T Y Your Beacon Fifth Wheel is constructed with safety as the top priority. This fifth wheel meets or exceeds the safety requirements and suitable codes in effect at the time it is built. All mandatory safety items are attentively installed to protect you and the tenants of your FAMILY SAFETY PLAN In case of emergency or severe weather conditions, we advise that you develop a Family...
  • Page 45: Pet Safety

    o CC uPa nT sa fe T Y • Never touch or use electrical components while feet are bare, while hands are wet, or while standing in water. • Improper grounding of the vehicle can cause personal injury. • Do not attach an extension cord to the utility power cord. •...
  • Page 46: Fire Extinguisher

    o CC uPa nT sa fe T Y • In a fire emergency, perform your Family Safety Plan. • Make sure everyone knows how to Stop, Drop & Roll if their clothes or any part of them catches on fire. •...
  • Page 47: Figure 3. Fire Extinguisher

    o CC uPa nT sa fe T Y Household fire extinguishers are classified into four types by Underwriters Laboratories (UL): Table 4. Fire Extinguisher Types rating intended use Type A For use on fires involving combustible materials such as wood, cloth and paper. Type B For use on flammable liquid fires, including kitchen grease.
  • Page 48: Emergency Egress Window

    o CC uPa nT sa fe T Y operation To operate a fire extinguisher, remember the word: P.A.S.S. P ull the pin. Hold the extinguisher with the nozzle pointing away from you, and release the locking mechanism. Aim low. Point the extinguisher at the base of the fire. Squeeze the lever slowly and evenly.
  • Page 49: Figure 4. Emergency Egress Window

    o CC uPa nT sa fe T Y Figure 4. Emergency Egress Window • For safety reasons, when you arrive at the campsite be mindful that the egress window should never be blocked. • When finding a place to park, monitor your surroundings around the egress window and make sure that the ground is safe to escape in case of an emergency.
  • Page 50: Smoke Alarm

    o CC uPa nT sa fe T Y S M O K E A L A R M The smoke alarm is wired to go off once the smoke makes contact with the alarm. The alarm is created for your safety. In your RV, the smoke alarm is placed above the stairway on the ceiling.
  • Page 51: Carbon Monoxide (Co)

    o CC uPa nT sa fe T Y How to test One every three months, text your smoke alarm. While testing your alarm, stand a few feet back so that it does not cause damage to your hearing. Hold down the test button until it alarms. After releasing your finger, it might still sound for a couple seconds but do not be concerned that is normal.
  • Page 52: Co/Lp Gas Alarm

    o CC uPa nT sa fe T Y to assure that CO levels do not rise to dangerous levels within the RV. In sufficiently high concentrations, CO can kill in minutes. The following symptoms are related to co exposure or poisoning: •...
  • Page 53: Figure 6. Propane/Co Alarm

    o CC uPa nT sa fe T Y Figure 6. Propane/CO Alarm ”Indoor Air Quality” on page 53 and “Chemical Sensitivity & Offgassing” on page If the alarm sounds EVERYONE should exit the fifth wheel. Allow the inside of the coach to vent by opening windows, etc.
  • Page 54: Indoor Air Quality

    o CC uPa nT sa fe T Y Testing the co/propane gas alarm If you are camping, storing, or traveling frequently, then you should test the gas alarm after each of these events. Once every three months, test the propane alarm. Replace the alarm instantly if it does not pass the test.
  • Page 55: Chemical Sensitivity & Offgassing

    o CC uPa nT sa fe T Y EPA recommendations Environmental Protection Agency, (EPA) provides three methods for better air quality: Eliminated sources: To lessen the source of pollution, see the following elements that contribute to contaminating the air and limiting them will help with better air quality: •...
  • Page 56: Formaldehyde

    o CC uPa nT sa fe T Y F O R M A L D E H Y D E Formaldehyde is a chemical that is very hypersensitive for some people while others it is not an issue. The reason for so much safety consideration is based off of the sensitivity of formaldehyde.
  • Page 57 o CC uPa nT sa fe T Y coNDENSATIoN Condensation refers to the water droplets that appear on a cold surface as water vapor in the air cools, changing to liquid water. In cold weather, it may be seen as frost or ice. Mois- ture can condense on the inside of an RV during cold weather the same way that moisture collects on the outside of a cold glass during humid weather.
  • Page 58: Where There Is Moisture, There May Be Mold

    o CC uPa nT sa fe T Y • Manage the inside temperature during cold weather. The warmer temperatures inside your RV will cause condensation to form on areas that are not well insulated (ie., win- dows, vents, wall studs, etc.). WHERE THERE IS MoISTURE, THERE MAY BE MoLD Mold is a microscopic organism that can live in virtually any indoor or outdoor environ- ment.
  • Page 59: Cold Weather Use

    o CC uPa nT sa fe T Y coLD WEATHER USE Please keep in mind, that your RV is not designed for use during sub-freezing weather. If you plan to use your RV in freezing (or below freezing) temperatures, the following precautions MUST to be taken: •...
  • Page 60: Pre-Travel Information

    P R E - T R A V E L I N F O R M A T I O N To help ensure your traveling enjoyment, update your GPS (customer supplied) and confirm that your route is planned with current road maps. Call ahead for tourist information for the areas that you will be visiting or traveling through.
  • Page 61 Pre- T raV el inforM aTion • Understand all propane safety warnings and follow manufacturer recommended operat- ing procedures. WARNING PRoPANE GAS IS FLAMMABLE, IMPRoPER USE MAY RESULT IN A FIRE oR EXPLoSIoN. Passenger safety W0ARNING WHILE YoUR RV IS IN MoTIoN, Do NoT ALLoW ANYoNE To RIDE INSIDE AS A PASSENGER.
  • Page 62: Towing

    ToW ing T O W I N G TOWING • As a minimum requirement, the towing capacity of your tow vehicle MUST be greater than the Gross Vehicle Weight Rating (GVWR) of your RV. NOTE: Manufacturer-advertised tow ratings for vehicles may not reflect the tow rating of your particular vehicle.
  • Page 63: Weight Labels

    ToW ing GAWR (Gross Axle Weight Rating) — GAWR is the maximum weight each axle is designed to carry. GVWR (Gross Vehicle Weight Rating) — GVWR (also called Maximum Loaded Trailer Weight) includes the GAWR plus the hitch weight. It is the maximum allowed weight for a fully load- ed RV or tow vehicle.
  • Page 64: Cargo Capacities

    ToW ing Tire and Loading Information Label This label specifies the maximum amount of cargo that can be safely added to the RV. It is located on the driver’s side exterior, just forward of the propane tank. Figure 9. Tire and Loading Information Label (Example) (Located on the Forward, Off-Door-Side Exterior) C A R G O C A P A C I T I E S When loading cargo into your RV, Do NoT exceed:...
  • Page 65: Loading Your Rv

    ToW ing For example, if your RV’s: • Tires are each rated at 2,000 lbs. 2,000 lbs. x 4 tires = 8,000 lbs. • Gross Weight is 9,000 lbs. • with a hitch weight of 1,200 lbs. then 9,000 lbs. - 1,200 lbs. = 7,800 lbs. The actual weight on the RV tires is 7,800 lbs., This is under the load rating of the tires.
  • Page 66 ToW ing will void the Limited Base Warranty and Limited Structural Warranty, and the warranties of many component part manufacturers. Have your RV weighed periodically at a public scale to determine the proper load distribu- tion. Keep in mind that individual scales will operate differently. The surroundings of the scale need to be adequate to accommodate weighing each side of your RV.
  • Page 67: Recommended Tire Pressure & Load Limits

    ToW ing With these actual weights, it is now possible to compare them against the Trailer Weight Information label weight ratings to ensure you are below the posted minimum ratings. REcoMMENDED TIRE PRESSURE & LoAD LIMITS TIRE PRESSURE & LOAD LIMITS The major causes of tire failure are under-inflated tires and overloaded vehicles.
  • Page 68: Rv Driving Schools & Seminars

    ToW ing • ALWAYS wear your seatbelt and obey all traffic laws. • DO NOT exceed the posted speed limit. • Many states have lower speed limits for tow vehicle/RV combinations. • ALWAYS be a courteous and alert driver. • Watch out for other drivers, bicyclists and pedestrians.
  • Page 69: Rv Braking System

    ToW ing RV BRAKING SYSTEM The RV brakes are designed to work with your tow vehicle brakes. To maintain proper brak- ing performance, both the RV and tow vehicle brakes must be used together. Separate use of the braking systems will cause accelerated wear and damage. When your RV is new, it is impossible to adjust the brake shoes precisely.
  • Page 70: Axles

    ToW ing AXLES Your trailer has two 8,000 lb axles. Table 5. Trailer Axle Maintenance Schedule 3 Months 6 Months 12 Months or every or every or every item function required Weekly 3,000 6,000 36,000 Miles Miles Miles Brakes Test that they are At Every Use operational.
  • Page 71: Tow Vehicle Battery

    ToW ing 3 Months 6 Months 12 Months or every or every or every item function required Weekly 3,000 6,000 36,000 Miles Miles Miles Wheel Nuts Tighten to specified ◆ and Bolts torque values. Wheels Inspect for cracks, ◆ dents, or distortion. Tire Inflation Inflated tires to MFG’s ◆...
  • Page 72: 7-Way Wire Harness/Connector Plug

    ToW ing Table 6. Brake Controller Compatibility Manufacturer Vehicle Years/ Compatible Compatible if used Controller Models with Hba-CaM Ford Vehicles 2005-2017 2007-2017 2009-2017 Dodge 2010-2019 GMC/Chevy 2007-2017 NOTE: The above table is for HBA-CAM 2 Cargo Towing Solutions (formerly Carlisle) HydraStar Control Adapter Module for Hydra Star Electric-Over-Hydraulic (EOH) Brake Actuators.
  • Page 73: Breakaway Switch

    ToW ing Maintenance The connector plug may build up corrosion with extended use and should be cleaned pe- riodically to insure good electrical contact. Make sure the connector plug is kept clean and protected from road elements as you travel. The wiring of that connector is shown in the accompanying diagram.
  • Page 74: Welded Rear Hitch (If So Equipped)

    ToW ing Fifth wheel pin box height There is no recommended hitch height for fifth wheels; usually the fifth wheel pin box is adjustable for variance in trucks and truck suspension systems. Adjust the hitch assembly so the tow vehicle and the fifth wheel are essentially level. A high hitch will transfer weight behind the axles and cause the vehicle to fishtail.
  • Page 75: Unhitching

    ToW ing Check that the fifth wheel landing legs are fully RETRACTED. Attach the breakaway switch cable to the tow vehicle. Leave enough slack to accom- modate tight turns. Connect the 7-way wire harness from the fifth wheel to your tow vehicle and secure in the travel position.
  • Page 76 ToW ing Allow more time to go around the vehicle you are passing. You cannot cut back into the traffic lane as quickly due to the longer length of your tow vehicle/RV combination. Drive with caution to avoid situations that might require quick momentum changes. The required stopping distance is greatly increased when towing an RV.
  • Page 77 ToW ing Turning corners When turning, the tires do not follow the path of your tow vehicle tires. The RV will make a tighter turn than the tow vehicle. You must compensate for this action by carefully pulling the tow vehicle out into the intersection further than you would normally so that the RV clears the curb (or any parked vehicles along the curb).
  • Page 78: Roadside Emergency

    R O A D S I D E E M E R G E N C Y A roadside emergency can happen at any time. ALWAYS carry an emergency kit with three red warning signs (or indicators) to display if necessary. If you must make an emergency roadside stop: •...
  • Page 79: Tires

    T I R E S TIRE MAINTENANCE TIRE SAFETY INFoRMATIoN This portion of the Owner’s Manual contains tire safety information as required by 49 CFR 575.6(4) and is based in part on the National Highway Traffic Safety Administration’s (NHTSA) brochure titled Tire Safety, Everything Rides On It.
  • Page 80: Tire Safety Tips

    T ire s ufacturers must report all materials used in the composition of the tire, ie., steel, nylon, polyester, etc. TIRE SAFETY TIPS Preventing tire damage • DO NOT run over curbs or foreign objects in the roadway or when parking. •...
  • Page 81: Tire Balance And Wheel Alignment

    T ire s TIRE BALANcE AND WHEEL ALIGNMENT To avoid vibration or shaking of the vehicle when a tire rotates, the tire must be properly balanced. This balance is achieved by positioning weights on the wheel to counterbalance heavy spots on the wheel-and-tire assembly. A wheel alignment adjusts the angles of the wheels so that they are positioned correctly relative to the vehicle’s frame.
  • Page 82: Figure 15. Tire

    T ire s Inspect your tires regularly for uneven tread wear. Table 7. Tire Wear Patterns Wear Pattern Possible Cause solution Edge Wear Fill tire with an air compressor Thin Tread Wear on Under Inflation to the recommended cold tire Tire Edges pressure center Wear Press tire valve stem, slowly release...
  • Page 83: Tire Pressure

    T ire s T I R E P R E S S U R E Load Limits are determined by the tire size and the greatest amount of weight each tire can safely carry. Tire Pressure is the amount of air pressure a tire requires to be properly inflated. It is mea- sured in pounds per square inch (PSI).
  • Page 84: How Overloading Affects Your Rv And Tires

    T ire s Steps for maintaining proper tire pressure Locate the recommended tire pressure on the RV’s Tire and Loading Information label located on the forward, off-door-side exterior. Check the tire pressure of all tires. a. If the tire pressure is too high in any of the tires, slowly release air by gently press- ing on the tire valve stem with the edge of your tire gauge until you get to the correct pressure.
  • Page 85: Us Dot Tire Identification Number (Tin)

    T ire s US D oT TIRE IDENTIFIcATIoN NUMBER (TIN) Table 8. US DOT Tire Identification Number (TIN) Example • This begins with the letters “DOT” and indicates that the tire meets all federal standards. • The next two numbers or letters are the plant code where it was manufactured •...
  • Page 86: Tire Size & Type Designation

    T IRE S TIRE SIZE & TYPE DESIGNATIoN The tires on your unit are marked with a tire size and type designation: 215/75R17.5. The designation breakdown is as follows: Table 9. Tire Size and Type Designation The first three-digit number gives the width in millimeters of the tire from sidewall edge to sidewall edge.
  • Page 87: Spare Tire

    T ire s Tires are warrantied by the tire manufacturer, not by Vanleigh RV. If you need tire warranty assistance, please contact LionsHead Specialty Tire & Wheel. SPARE TIRE The spare tire is used if a trailer tire is damaged, flat, or loses air pressure. The spare tire/ wheel may differ from the original equipment, and is intended for temporary use only.
  • Page 88: Tire Changing

    T ire s Figure 20. Spare Tire Winch Access Hole Figure 21. Crank Handle T I R E C H A N G I N G TIRE CHANGING TIRE cHANGING BASIcS NOTE: A Hydraulic Jack and Jack Stands (for changing a tire) are customer supplied. “Roadside Emergency”...
  • Page 89: Figure 22. Torque Digram

    T ire s Place a Hydraulic Jack on the frame close to the spring hanger. Raise the trailer until the tire clears the ground. NEVER attempt to use a stabilizer jack to lift the RV. Set up a Jack Stand under the frame just to the rear of the tire being changed, then change your tire.
  • Page 90: Table 11. Wheel Nut Torque

    T ire s Table 11. Wheel Nut Torque Wheel size stud size Torque sequence 1st stage 2nd stage 3rd stage 17.5” w/ cone nut 5/8” 50–60 100–120 190–210 *NOTE: All torque in ft.–lbs. VA N L E I G H B E A c o N...
  • Page 91: Leveling

    l e V eli n g L E V E L I N G LEVELING AUToMATIc LEVELING SYSTEM After unhitching your RV, you need to ensure it is level. Leveling is very important. A level RV is more comfortable for sleeping and walking inside. The water drainage systems are de- signed with proper slope and must be level for proper operation.
  • Page 92: Level-Up With Onecontrol Touch Panel

    L E V E L U P W I T H O N E C O N T R O L ™ T O U C H P A N E L Level-Up With OneControl Touch Panel ® OWNER'S MANUAL ™...
  • Page 93 L E V E L - U P T A B L E O F C O N T E N T S System Information Safety Information Touch Pad Diagram - Auto Leveling Control Red/Green LED Indicator Operation - Auto Leveling Control Touch Pad Unhitching Instructions Auto Level Auto Level Sequence...
  • Page 94: System Information

    System Information The LCI Level-Up® OneControl Touch Panel is an automatic leveling system control for fifth wheel applications. It interfaces to the LCI Level-Up pump/jack system to level the trailer. The system utilizes one S Y S T E M I N F o R M AT I o N main control board and a separate waterproof remote level sensor to measure and manage level point, and can be operated from several user interface devices, including: Auto Leveling Control Touch Pad - Mounted outside the trailer within view of the hitch.
  • Page 95: Table 12. Level-Up Touch Pad Diagram - Auto Leveling Control

    Touch Pad Diagram - Auto Leveling Control Fig. 1 T o U c H PA D D I A G R A M - A U T o L E V E L I N G c o N T R o L RED/GREEN LED INDIcAToR Table 12.
  • Page 96: Operation - Auto Leveling Control Touch Pad

    Operation - Auto Leveling Control Touch Pad Unhitching Instructions o P E R AT I o N - A U T o L E V E L I N G c o N T R o L T o U c H PA D NOTE: Prior to unhitching from the tow vehicle, ensure trailer is parked on a level surface and chock the tires of the trailer.
  • Page 97: Table 14. Level-Up Touch Panel Diagram

    Touch Panel Diagram - MyRV OneControl Touch Panel T o U c H PA N E L D I A G R A M - M Y R V o N E c o N T R o L T o U c H PA N E L Fig.
  • Page 98: Standard Mode And Menu

    Operation - MyRV OneControl Touch Panel Operation - MyRV One Control Touch Panel Standard Mode and Menu To reach Standard Mode (Fig. 2) for leveling: STANDARD MoDE AND MENU Power on the OneControl Touch Panel (Fig. 2K). Press "MyRV Control Panel" on the main screen. Press the "Leveler"...
  • Page 99: Unhitching Instructions

    Unhitching Instructions NOTE: Prior to unhitching from the tow vehicle, ensure trailer is parked on a level surface and chock the tires of the trailer. UNHITcHING INSTRUcTIoNS Push touch panel “ON/OFF” (Fig. 2K) to turn system on (See "Standard Mode and Menu" to reach standard mode.) AUTo LEVEL Push "EXTEND"...
  • Page 100: Zero Point Calibration

    Zero Point Calibration The “Zero Point” is the programmed point that the trailer will return to each time the Auto Level feature is used. The “Zero Point” must be programmed prior to using the Auto Level feature to ensure the proper operation of the system.
  • Page 101: Touch Pad Diagram - Onecontrol App From Myrv

    10 0 10 0 Fig. 8 Fig. 9 T o U c H PA D D I A G R A M - o N E c o N T R o L A P P F R o M M Y R V Touch Pad Diagram - OneControl App From MyRV NOTE: The One Control Leveling App is available on iTunes for iPhone and iPad and also on Google Play for Android users.
  • Page 102: Table 15. Level-Up Touch Panel Diagram

    1 0 1 1 0 1 Callout Description Jack Buttons - Select front, rear, right and left jacks to be operated depending on mode. Jacks available to be operated will be highlighted in blue. In Standard Mode o P E R AT I o N - o N E c o N T R o L A P P (Fig.
  • Page 103: Standard Mode And Menu

    Standard Mode and Menu Standard Mode is the mode launched when the OneControl app "Leveler" function is powered up. The screen will show the system menu (Fig. 10). The front jacks can be extended/retracted in Standard Mode. STANDARD MoDE AND MENU Rear jacks can be retracted from this mode.
  • Page 104: Table 16. Level-Up Touch Panel Diagram - Linc Remote Control

    1 0 3 1 0 3 Unhitching Instructions NOTE: Prior to unhitching from the tow vehicle, ensure trailer is parked on a level surface and chock the tires of the trailer. UNHITcHING INSTRUcTIoNS Push "Extend" (Fig. 10I) and "FRONT" buttons (Fig. 10) to extend front jacks and lift front of trailer to take the weight of the trailer off of the hitch.
  • Page 105: Configuring Linc Remote To Sync To Myrv Onecontrol Touch Panel

    10 4 10 4 Fig. 13 coNFIGURING LINc REMoTE To SYNc To MYRV oNEcoNTRoL ToUcH PANEL Configuring Linc Remote to Sync to MyRV One Control Touch Panel Turn on the Linc remote control (Fig. 13I) and enter a PIN. Choose "Leveler" from the menu screen. Turn on the MyRV OneControl Touch Panel (Fig.
  • Page 106: Basic Jack Operation

    1 0 5 1 0 5 Fig. 16 Fig. 17 BASIc JAcK oPERATIoN UNHITcHING INSTRUcTIoNS AUTo - LEVEL AUTo LEVEL SEQUENcE Basic Jack Operation Press RETRACT (Fig. 13A) or EXTEND (Fig. 13B) and "front" arrow (Fig. 13D) to operate front jacks. Press RETRACT or EXTEND, then "rear"...
  • Page 107: Maintenance

    10 6 10 6 NOTE: If the Auto Level sequence does not perform as described above, test that the jacks operate correctly by pushing their coordinating buttons on the Linc remote; e.g., "FRONT" button operates M A I N T E N A N c E only the front jacks, etc.
  • Page 108 Locate the valves that are paired with the front jacks or rear jacks to be manually overridden. A. Front jacks - Valve located on the front jacks (Fig. 18). B. Rear Jacks - Valve located on manifold (Fig. 19). DO NOT over-tighten override set screws, as this can damage the valves. 5/32 Using a ”...
  • Page 109: Table 17. Level-Up Troubleshooting - Error Display In Lcd Screen

    10 8 10 8 Troubleshooting T R o U B L E S H o o T I N G Error Display In LCD Screen Faults can only be cleared via the OneControl Touch Panel or OneControl Leveling App through MyRV. The only exception is when the Auto Leveling Control mini-touch pad (Fig.
  • Page 110: Level-Up ® Towable Octp Assembly

    1 0 9 1 0 9 LEVEL-UP TOWABLE OCTP ASSEMBLY ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P A S S E M B LY ® 14K Landing Gear (x2) Controller OneControl™...
  • Page 111: Table 18. Level-Up Towable Octp Components

    LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ® NOTE: Part numbers are shown for identification purposes only. Not all parts are available for individual sale. All parts with a link to the Lippert Store can be purchased.
  • Page 112 11 1 11 1 LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ®...
  • Page 113 LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ® 8K Jacks Gen I Gen II Gen I Gen II...
  • Page 114 1 1 3 1 1 3 LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ®...
  • Page 115 LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ® Callout Part # Description 232201 Rear Sensor...
  • Page 116 1 1 5 1 1 5 LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ®...
  • Page 117 LEVEL-UP TOWABLE OCTP COMPONENTS ® LEVELING AND STABILIZATION L E V E L - U P T o WA B L E o c T P c o M P o N E N T S ® Callout Part # Description 138420 Manifold...
  • Page 118: Notes

    1 1 7 1 1 7 Notes N o T E S VA N L E I G H B E A c o N VA N L E I G H B E A c o N 1 1 7 1 1 7 Page 27 Rev: 03.25.19...
  • Page 119 The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”).  LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided.  Any unauthorized use shall void any applicable warranty.  The information contained in this manual is subject to change without notice and at the sole discretion of LCI. ...
  • Page 120: Electrical Systems

    1 1 9 1 1 9 E L E C T R I C A L S Y S T E M S The electrical system on your Beacon fifth wheel is comprised of two independent electri- cal systems. One system is 120-volt 60HZ AC power (shore), and the other is 12VDC power (battery).
  • Page 121: Figure 23. 50-Amp Power Cord

    1 20 e leC T riC a l sY sTe M s Figure 23. 50-Amp Power Cord connecting the power cord Turn OFF the load center main 120-volt circuit breaker. Carefully extend the entire length of the power cord from the electric cable hatch to the external power source.
  • Page 122: Load Control Center

    e leC T riC a l sY sTe M s 1 2 1 To help prevent power surges from damaging the connected loads, please follow these instructions when hooking up to the external power source: a. Unplug the shore power cord when the RV is left unused. This may help limit po- tential damage in the event of a power surge.
  • Page 123 12 2 e leC T riC a l sY sTe M s • Power distribution panel provides power to AC and DC applications in your RV • AC section includes 12 branch circuits rated for 240V at 50 amps • DC section includes 18 branch fuse holders - wired for (4) 30 amp and (14) 20 amp fuses •...
  • Page 124: 120-Volt Ac System

    e leC T riC a l sY sTe M s 1 2 3 Converter Located Inside Figure 25. Power Control Center Inspection and maintenance If the 12V power converter is NOT working, or the battery system is not being charged: Locate the converter fuse panel on one end of the converter.
  • Page 125: 120-Volt Circuit Breakers

    12 4 e leC T riC a l sY sTe M s The following electrical components (if so equipped) will operate ONLY when your RV is connected to shore power: 120-volt to 12V power converter, air conditioner, 120-volt refrig- erator, wine chiller, microwave oven, television(s), fireplace, and other appliances that plug into convenience electrical receptacles.
  • Page 126: 120-Volt Ac (Vac) Receptacles

    e leC T riC a l sY sTe M s 1 2 5 120 V Breakers 12VDC Fuses Figure 26. 120-Volt Circuit Breakers Maintenance and replacement Circuit breaker switches can wear out. Test the breakers annually, at the beginning of the camping season.
  • Page 127: 12V Usb Receptacles

    12 6 e leC T riC a l sY sTe M s • If you should feel even the slightest of electrical shock, immediately disconnect the unit from the 120- VAC power source and locate the electrical fault (i.e.: typically, it is a break in the grounding circuit).
  • Page 128: Lp Generator

    e leC T riC a l sY sTe M s 1 2 7 Figure 28. 120VAC Receptacles Contact your dealer for assistance, if the RESET button does NOT restore 120-volt power or trips repeatedly. LP GENERAToR When purchasing your Vanleigh RV, you may have selected one of the following options: a generator or the preparations for a generator.
  • Page 129: Transfer Switch

    12 8 e leC T riC a l sY sTe M s WARNING failure To Turn “off” THe 120 - VaC aPPlianCes WHen sTarTing or sToPPing THe generaTor MaY daMage THe Transfer sWiTCH and/or eleCTriCal aPPlianCes. Figure 29. Generator Control Panel Refer to the Generator manual for additional information and maintenance instructions.
  • Page 130: 12-Volt Dc System

    e leC T riC a l sY sTe M s 1 2 9 Figure 30. Transfer Switch 12 - VoLT D c SYSTEM Many of your RV components including the light fixtures, water pump, motors and appli- ances run on 12V electricity. •...
  • Page 131: Batteries

    13 0 e leC T riC a l sY sTe M s Replacing a fuse Before replacing a fuse, always turn off the electrical component(s) protected by it. Disconnect the shore power cord. Disconnect the RV auxiliary battery main negative battery cable. Remove the fuse panel cover to check fuses.
  • Page 132: Battery Vent

    e leC T riC a l sY sTe M s 1 3 1 The RV battery which constitutes the 12-VDC system is contained in the front, outside com- partment. To access this battery, open the front, outside compartment door and remove the sealed battery cover.
  • Page 133: Battery Disconnect

    1 32 e leC T riC a l sY sTe M s Replacement and maintenance Even when the battery disconnect is turned OFF, some equipment in your RV will draw small amounts of current. To prevent the auxiliary battery from being discharged when your RV is not connected to shore line power, disconnect the battery negative cable at the bat- tery.
  • Page 134: Battery Inspection And Care

    e leC T riC a l sY sTe M s 1 3 3 Figure 32. Battery Disconnect Switch NOTE: Remember to reconnect the battery cables and turn ON the battery disconnect switch when you are ready to use the RV or perform periodic maintenance checkups.
  • Page 135: Spyder Control System

    13 4 e leC T riC a l sY sTe M s as grease may act as an insulator and keep the battery electrical power from entering the cables. Removing the battery If the battery is not going to be used for an extended period of time, it should be removed from the RV and stored in a cool, dry place (40-60°...
  • Page 136: Figure 33. Spyder Control Unit

    e leC T riC a l sY sTe M s 1 3 5 Figure 33. Spyder Control Unit Figure 34. Spyder Lights Screen IMPoRTANT: Some lights are on a dimmer switch. Press and hold the light button and to access the Dimming control Screen. Figure 35.
  • Page 137: Calculating Electrical Load

    13 6 e leC T riC a l sY sTe M s NOTE: A Mira Module can be purchased which will enable you to control the Spyder system via Bluetooth from your phone or tablet. Contact Firefly Integrations for additional information. Phone: (574) 825-4600 http://www.fireflyintegrations.com/ or email: support@fireflyint.com.
  • Page 138: Approximate Electrical Load Ratings

    e leC T riC a l sY sTe M s 1 3 7 APPRoXIMATE ELEcTRIcAL LoAD RATINGS Refer to the actual amperage of the appliance when possible. (Watts ÷ 120) Table 19. Approximate Electrical Load Table 20. Approximate Electrical Load Ratings—120 Volt System Ratings—12 Volt System 120 Volt system 12 Volt system...
  • Page 139: Plumbing Systems

    13 8 13 8 P L U M B I N G S Y S T E M S There are two separate water systems in your RV, the Fresh Water System and the Waste Water System. • The Fresh Water System consists of the fresh water holding tank, fresh water connec- tions, water pump, water heater, faucets, shower or tub, water filter system and outside shower assembly.
  • Page 140: Plumbing Functions Within The Spyder Controls

    Plu M b ing sY sTe M s 1 3 9 Figure 37. Sanitize the Water Tank before First Use Small amounts of contaminants and minerals are found in ALL water. They can sometimes cause your fresh water to have an odor. Usually, untreated well water is the source of water system odors.
  • Page 141: 12V Water Pump

    1 40 Plu M b ing sY sTe M s Figure 38. Spyder Control Unit 12V WATER PUMP Once activated, the water pump will self-prime and provide water. The water pump contin- ues to run until approximately 45 lbs. of pressure is achieved and shut off. The water pump will automatically restart when pressure drops.
  • Page 142: Fresh Water Holding Tank

    Plu M b ing sY sTe M s 1 41 FRESH WATER HoLDING TANK The fresh water tank can be pressure filled using the fresh water inlet, with the valve point- ed to “Tank Fill.” A plastic overflow tube is plumbed into the fresh water holding tank to allow water to flow out of the water tank.
  • Page 143: Water Pressure Regulator (Customer Supplied)

    1 42 Plu M b ing sY sTe M s WATER PRESSURE REGULAToR (cUSToMER SUPPLIED) Excessive pressure from water supply systems may be encountered in some parks, especial- ly in mountain regions. Water pressure regulators can protect your system against such high pressure.
  • Page 144: Figure 43. Water Heater-Truma (Optional)

    Plu M b ing sY sTe M s Figure 43. Water Heater—Truma (Optional) Near the water heater (behind an access panel) are hot and cold water shutoff valves that isolate the water heater. These valves are to be used when the water heater is being worked Figure 44.
  • Page 145: Figure 45. Truma Interior Control Dial

    14 4 Plu M b ing sY sTe M s • Always open both the hot and cold water faucets when filling the fresh water tank to allow air pockets to be forced out of the water system. operating the Truma AquaGo comfort water heater NOTE: The Truma AquaGo heats using propane only (but uses electricity for ignition).
  • Page 146: Figure 47. Pressure And Temperature Relief Valve

    Plu M b ing sY sTe M s Refer to the water heater manufacturer’s owner manual for details on eliminating the odor from sulfur water. High altitude deration Operation of the water heater at high altitudes may require derating. If the water heater is not properly derated, lack of sufficient oxygen for combustion may produce improper burner operation.
  • Page 147: Bathroom Shower

    1 46 Plu M b ing sY sTe M s For information on draining and winterizing the water heater, see “Water Heater Draining and Winterization” on page 163. BATHRo oM SHoWER Unlike your home, the RV does not contain a water pressure balance valve. Keep aware of the water heater and holding tank capacities.
  • Page 148: Outside Shower

    Plu M b ing sY sTe M s 1 47 Shower surround maintenance The shower walls in your RV are fiberglass. Use a mild detergent soap and warm water to clean. NEVER use gritty or abrasive particle soaps or scouring compounds to clean the plastic.
  • Page 149: Faucets

    1 48 Plu M b ing sY sTe M s FAUcETS The faucets inside your RV operate much the same way as the faucets in your home. Make sure there is sufficient water available and, if dry camping, the 12V water pump is turned ON before operating.
  • Page 150: Figure 52. Bathroom Sink Shutoff Valves

    Plu M b ing sY sTe M s 1 49 Figure 52. Bathroom Sink Shutoff Valves Figure 53. Kitchen Sink Shutoff Valves VA N L E I G H B E A c o N 1 4 9...
  • Page 151: Water Control System

    15 0 Plu M b ing sY sTe M s WATER coNTRoL SYSTEM Your Beacon Fifth Wheel is equipped with an Anderson Brass Kantleak Valve System. NOTE: The pointed end of the valve points to what is selected. Figure 54. Andersen Kantleak Valve System Draining and winterizing If the RV is to be exposed to freezing temperatures while stored, the water heater must be drained to prevent damage from freezing.
  • Page 152: Figure 56. Water Heater Bypass Valve

    Plu M b ing sY sTe M s 1 5 1 Open all faucets, including the outside shower. Open the fresh water tank drain valve. See “Figure 41. Water Tank Drain and Overflow” on page 141. Open red and blue low point drain lines, located in the wet bay. Set the water heater bypass valve to Normal (vertical).
  • Page 153: Sanitizing The Fresh Water System

    Plu M b ing sY sTe M s NOTE: ALWAYS use the water heater P & T Valve (pressure and temperature valve) to relieve the water pressure, BEFORE you remove the water heater drain plug. If you do not relieve the water pressure, water will spray out of the opening when the drain plug is removed.
  • Page 154: Figure 59. Water Filter Housing

    Plu M b ing sY sTe M s 1 5 3 Figure 59. Water Filter Housing To sanitize the fresh water system: Level the RV. Drain fresh water system. Make sure the low point drain valves are closed. Connect a hose to the city water port. Put the other end of the hose into a container of sanitizing solution.
  • Page 155: Figure 61. Sanitizing The Fresh Water System

    15 4 Plu M b ing sY sTe M s Turn the selector valve to PUMP. Figure 61. Sanitizing the Fresh Water System Operate all faucets until the sanitizing fluid has come through, then Turn OFF the pump. Allow solution to stand for three (3) hours. DRAIN tank and FLUSH the system with fresh water.
  • Page 156: Black/Gray Water System

    Plu M b ing sY sTe M s 1 55 If you are traveling in an area where the water has high iron and sulfur content, add to the water filter housing one tablespoon of chlorine bleach to every 10 gallons of water in your tank.
  • Page 157: Toilet

    15 6 Plu M b ing sY sTe M s ToILET Aquamagic Tecma Figure 62. Toilet operation: AquaMagic Toilet • BEFORE use: FLUSH the toilet several times, releasing enough water to cover the bottom of the holding tank. • ALWAYS maintain four to six inches (10-15 cm) of water in the toilet for better sanitation system performance.
  • Page 158: Figure 63. Tecma Toilet Controls

    Plu M b ing sY sTe M s 1 5 7 Not lighted: System Off Green: Toilet System On and tank less than half full Yellow: Toilet system is on and holding tank is at least half full Red: Toilet system is on and holding tank is full Red Warning Light: Tank is full and lockout is disabled.
  • Page 159: Drain Pipes With Hepvo Valve

    15 8 Plu M b ing sY sTe M s cleaning and maintenance Clean the toilet regularly. DO NOT use chlorine (undiluted) or caustic chemicals in the toilet system (i.e., laundry bleach or drain opening chemicals). These products damage the seals in toilets and dump valves.
  • Page 160: Black/Gray Water Holding Tanks

    Plu M b ing sY sTe M s BLAcK/GRAY WATER HoLDING TANKS When connected to the sewer drain line at a campground, keep the black tank drain valve closed until the holding tank is at least 3/4 full. This should provide sufficient water to assist in complete draining of the black water holding tank.
  • Page 161: Black Tank Flush

    16 0 Plu M b ing sY sTe M s Figure 66. Sewer Outlet Connection (Termination Valve) Place the other end of the sewer hose into the approved dump station. Open the gate valve by flipping the switch “on.” The tank will start to drain as soon as the switch is flipped.
  • Page 162: Figure 67. Black Tank Flush Line

    Plu M b ing sY sTe M s 1 61 To flush the tank after dumping: Leave the sewer hose connected to the outlet pipe. Ensure that it is routed to the dump station inlet. Attach a garden hose to the black tank flusher inlet. Do NoT use your fresh water hose.
  • Page 163: Figure 68. Gate Valve

    16 2 Plu M b ing sY sTe M s Figure 68. Gate Valve 1 6 2 VA N L E I G H B E A c o N...
  • Page 164: Winterization

    1 6 3 1 6 3 W I N T E R I Z A T I O N WINTERIZATION Preparing your RV for cold weather storage is very important for most states and Canada. Failure to prepare your RV may cause water supply lines and the water heater to freeze. IMPORTANT: Freezing of the water system can cause major system damage.
  • Page 165: Winterizing

    16 4 W in T eri Z aTio n Figure 69. Low-Point Drains located under the RV Relieve pressure on the water heater, by lifting the pressure relief valve. WARNING THe WaTer in THe WaTer HeaTer MaY be HoT and Can Cause seVere burns. Remove the drain plug to drain on the water heater.
  • Page 166: Figure 70. Water Pump Switch

    W in T eri Z aTio n 1 6 5 b. Open the fresh water tank drain valve. See “Figure 41. Water Tank Drain and Over- flow” on page 141. c. Open red and blue low point drain lines located in the wet bay. d.
  • Page 167: Figure 72. Ice Maker Valve In Wet Bay

    16 6 W in T eri Z aTio n Figure 72. Ice Maker Valve in Wet Bay Drain the water supply line for refrigerator’s ice maker. A drain is located behind the forward end of the galley slide. Figure 73. Ice Maker Drain behind Galley Slide Make sure the water heater 12V interior control switch is off.
  • Page 168: Figure 75. Anderson Valve Position For Winterizing

    W in T eri Z aTio n At the wet bay, turn the red Anderson Valve to Bypass and the black Anderson Valve to Winterize. Figure 75. Anderson Valve Position for Winterizing OPEN the fresh water tank drain Overflow Tube Drain Valve Figure 76.
  • Page 169: Figure 78. Winterization Fill

    16 8 W in T eri Z aTio n NOTE: Make sure to have enough RV antifreeze to winterize all fresh water lines. Several gallons may be required. Remove the water filter from the water filter housing and reattach the filter housing. Insert the short hose into a container of RV antifreeze solution attach the other end to the winterization fill.
  • Page 170: Dewinterizing

    W in T eri Z aTio n NOTE: As an alternative to adding antifreeze, you can blow out the fresh water lines with compressed air (max 70 PSI). DEWINTERIZING To dewinterize your vehicle, open both of the low point drains to allow the antifreeze solution to drain from the water system.
  • Page 171: Propane System

    P R O P A N E S Y S T E M PRoPANE GAS PROPANE GAS SYSTEM The propane system includes the propane cylinders, propane regulator, hoses, piping and copper tubing lines to each gas appliance. Follow the manufacturer’s instructions for each propane appliance and all safety precautions.
  • Page 172: Propane Gas Cylinders

    Pro Pa ne sY sTe M 1 7 1 nections soon after your purchase. System should also be checked when the propane tanks are filled for the first time, and again after 5,000 miles of travel. Continue propane system checks by a qualified propane service representative (at least once a year) as part of your normal maintenance.
  • Page 173: Propane Leak Test

    17 2 Pro Pa ne sY sTe M DOT (Department of Transportation) cylinders are the most common for use on RV trailers. DOT cylinders equipped with an OPD and ACME type 1 service valve are identified by the triangular service valve knob. Max output is 200,000 BTU/hr.
  • Page 174: Propane Alarm

    Pro Pa ne sY sTe M 1 7 3 NEVER use a solution containing ammonia or chlorine when locating leaks. These products are corrosive to copper gas lines and brass fittings, which could result in deterioration of the copper and brass components. If a leak is not fixed by tightening the connection, shut OFF the propane system valve(s) and immediately contact your dealer.
  • Page 175: Propane Regulator

    1 74 Pro Pa ne sY sTe M PRoPANE REGULAToR The two-stage regulator has the only moving components in the propane system. Its sole function is to reduce the pressure from the propane containers to a safe and consistent low operating pressure.
  • Page 176: Lp Distribution System

    Pro Pa ne sY sTe M 1 75 the empty cylinder to have it refilled without interrupting the flow from the full bottle. After filling the cylinder, connect the pigtail hose and slowly open the bottle valve. Figure 81. LP Gas Regulators The regulator has a vent to relieve excess pressure on the inlet side of the regulator should excess pressure develop in the gas tank and connecting gas line to that regulator inlet.
  • Page 177: Recommended Practices

    Pro Pa ne sY sTe M Remember, the main valve at the LP-gas tank must be closed whenever any gas appliance is to be installed, removed, or serviced. This process prevents LP-gas leakage which could result in a possible harmful explosion. If the odor of the LP gas is ever detected, immediate- ly discontinue use of any gas appliances and seek the services of a qualified service techni- cian.
  • Page 178: Cooking With Propane

    Pro Pa ne sY sTe M 1 7 7 can both contribute to the deterioration of these components, they must be inspected for wear at regular intervals. Be sure to inspect the hoses before each season and when having the tank refilled. Look for signs of deterioration such as cracks or loss of flexibility. When replacing the hose or other propane components, always replace them with components of the same type and rating (check with your dealer).
  • Page 179: Traveling With Propane

    17 8 Pro Pa ne sY sTe M TRAVELING WITH PRoPANE cAUTIoN before ToWing Your rV, ConfirM THaT THe ProPane ConTainers are ProPerlY fasTened in PlaCe. Turn off THe gas aT THe lP boTTle. THis disables all gas aPPlianCes and PiloT ligHTs. do noT oPeraTe THe ProPane sYsTeM WHen THe rV is in MoTion.
  • Page 180: Table 21. Average Propane Consumption Information

    Pro Pa ne sY sTe M 1 79 Most RV gas appliances are operated intermittently. Unless there is heavy use of hot water, the water heater consumption of propane is minimal. During cool temperature or high wind conditions, furnace consumption can be extremely high. To calculate your propane supply, take the BTU ratings for your propane appliances and divide that into the BTU availability.
  • Page 181: Appliances

    A P P L I A N C E S The following is a brief overview of the factory-installed, RV appliances and equipment. For detailed operating instructions for each specific component, please refer to the manufac- turer’s owner manuals (found in your Owner Information Package) or visit that manufactur- er’s website.
  • Page 182: Figure 84. Refrigerator

    a PP lia n C es 1 8 1 NOTE: The inverter is wired is to only power the refrigerator. Prior to departure, check to make sure that your inverter is powered ON after disconnecting from shore power. Figure 84. Refrigerator Figure 85.
  • Page 183: Wine Chiller

    1 82 a PP lia n C es WINE cHILLER A 12-bottle wine chiller is installed in the galley (select floorplans only). NOTE: Always remove any beverage from the wine chiller before storing the RV for winter. Figure 86. Wine Chiller WASHER/DRYER PREP If your RV was built with this feature, be aware the cabinet space provided is intended for the installation of an after-market RV-rated washer/dryer (customer supplied) only.
  • Page 184: Gas Cooktop

    a PP lia n C es 1 83 Figure 87. Washing Machine Shutoff Valves GAS co oKToP The RV is equipped with a standard, four-burner range. Figure 88. Gas Cooktop and Oven VA N L E I G H B E A c o N 1 8 3...
  • Page 185: Oven

    18 4 a PP lia n C es Igniting the cooktop While holding down the red direct spark ignition, press down on the gas control knob and turn it counter clockwise. Once the flame has ignited, continue holding the gas control knob for 2-3 seconds.
  • Page 186: Cooking With Propane

    a PP lia n C es The range hood (located on the bottom of the microwave) has both a light and fan control switch on the front panel. The aluminum mesh grease filter(s) (located on the underside range hood) of the can be gently hand-washed using mild soap and water. Consult the microwave owner’s manual in the Owner’s Information Package.
  • Page 187: Central Vacuum

    a PP lia n C es Flaming grease outside of the pan can be extinguished with baking soda or a multi- purpose dry chemical or foam-type fire extinguisher. cENTRAL VAcUUM A Dirt Devil vacuum is installed in the passthru. Starting the vacuum cleaner Lift the inlet valve cover on the wall.
  • Page 188: Figure 90. Vacpan Automatic Dust Pan

    a PP lia n C es 1 87 Figure 90. VacPan Automatic Dust Pan Figure 91. Central Vacuum Hose Connection Figure 92. Central Vacuum Bag Exchange Location VA N L E I G H B E A c o N 1 8 7...
  • Page 189: Electronics

    E L E C T R O N I C S The following is a basic overview of the audio/visual (A/V) electronics operation. The infor- mation in this section is written for original factory-installed equipment usage. If there have been modifications or replacements made to your electronics system then these instruc- tions may not apply (please contact the service center or technician who performed the modifications or substitutions if assistance is required).
  • Page 190: Figure 93. Furrion Radio/Dvd Player

    e leC T roniC s 1 89 • Clock/Alarm clock • 1x HDMI output for HD viewing • 2x RCA Audio/Video outputs for connecting 2 additional TVs • Coaxial and optical audio input connections on the rear of the CD/DVD player •...
  • Page 191: Television Sets

    e leC T roniC s TV operation Turn on the TV power supply. Turn on the TV and select your signal input using the “source” button. DVD operation Turn off the TV power supply. Turn ON the radio (the TV speakers are not used). Insert DVD to play.
  • Page 192: Figure 95. Living Room Tv

    e leC T roniC s 1 9 1 Figure 95. Living Room TV 43” HD LED TV (Bedroom TV) The 43” TV HDTV is located in the bedroom curbside wall. We install the TV with a coaxial cable with three different viewing options: SAT2 –...
  • Page 193: Tv Reception Basics

    e leC T roniC s Figure 96. Bedroom TV TV REcEPTIoN BASIcS TV broadcasting is a point-to-point communication. Any obstructions between the trans- mitter and the antenna will degrade the signal, affecting picture quality. • Television stations transmit their broadcast signal “over the air” to surrounding areas. •...
  • Page 194: Tv Roof Antenna

    e leC T roni C s 1 9 3 Figure 97. Antenna Signal Booster Switch TV Ro oF ANTENNA On the roof of the RV is a television antenna for receiving over-the-air television stations. Figure 98. Winegard 360+ Antennae To watch over-the-air stations, you must turn oN the antenna booster. This booster is locat- ed in a cabinet near the television.
  • Page 195: Cable/Satellite Outlet

    1 94 e leC T roni C s Turn ON power to TV Roof Antenna. Once the antenna is activated, you may automatically search for channels that are active in your area by editing and scanning the channels by using your remote control. Searching for channels Press the power button to turn the television ON.
  • Page 196: Satellite Prep

    e leC T roniC s 1 95 SAT1 to the receiver, then you will have a signal. The port labeled LRTV out is there if you want to connect the same receiver to the other two service ports located in the RV. One is located in the bedroom and the other is in the pass through storage compartment for outside viewing.
  • Page 197: Heating & Cooling

    1 96 He aT in g & Co ol ing H E A T I N G & C O O L I N G This section contains an overview of the RV heating and cooling components. It applies only to the original factory-installed equipment.
  • Page 198: Thermostat

    1 9 7 1 9 7 Fan Lid Open Fan Lid Close Fan ON/OFF Figure 102. Spyder Controls - Fans Figure 103. Bathroom Fan Touchpad Controls THERMoSTAT The following is a brief overview of how best to use the thermostat. For more detailed in- structions, please consult the thermostat literature in the Owner’s Information Package.
  • Page 199: Figure 104. Spyder Controls-Climate

    He aT in g & Co ol ing NOTE: In the “A/C” mode there will be a delay of several minutes before the refrigerant in the air conditioning system begins to cool the RV, as the compressor is on a time-delay circuit and it must also cool the ductwork to the vents first.
  • Page 200: Furnace

    He aT in g & Co ol ing 1 9 9 Figure 105. Temperature Sensor FURNAcE The RV is equipped with a forced-air furnace fueled by LP gas. The furnace requires both 12V power and propane gas for full operation. Make sure you have sufficient power available before operating your furnace.
  • Page 201: Figure 107. Furnace Ductwork

    20 0 He aT in g & Co ol ing Figure 107. Furnace Ductwork Figure 108. Furnace Discharge—Galley Figure 109. Furnace Discharge—Bedroom Using the furnace for the first time When the furnace is being used for the first time, there may be an initial “burn-off” of manufacturing compounds or residues left on the heat exchanger or in the ductwork which could produce odors, fumes, and possibly some smoke.
  • Page 202: Figure 110. Furnace Vent

    He aT in g & Co ol ing 20 1 To minimize the after-effects of this “burn-off” process, the initial use of the furnace should be done with all the doors and windows open to permit normal air circulation to dissipate these odors and fumes.
  • Page 203: Air Conditioning

    He aT in g & Co ol ing Before the beginning of each travel season • Thoroughly clean and inspect the furnace. • Remove any obstructions, debris, or lint which may obstruct free air flow or impede the operation of the air-circulation system. For example, accumulated dust or lint could pos- sibly obstruct the orifices for the pilot light or may accumulate on the blower blades and unbalance the operation of the blower.
  • Page 204: Figure 111. Air Conditioning Unit

    He aT in g & Co ol ing 20 3 Figure 111. Air Conditioning Unit Vents and Ducting The air-conditioned, cooled air is discharged through the louvered vents which are located in the ceiling throughout the entire RV. The return air vents run parallel to the discharge vents.
  • Page 205: Figure 113. Air Conditioning Return Vents

    20 4 He aT in g & Co ol ing Figure 113. Air Conditioning Return Vents Figure 114. Galley Return Air cooling vs. heat gain The roof air conditioner can, at best, cool the air it intakes by 20°F. During hot weather, through the day, your RV will absorb heat, increasing the inside temperature.
  • Page 206: Fireplace

    He aT in g & Co ol ing 20 5 Avoid the use of heat producing appliances. SET the air conditioner Fan/Cooling mode to HIGH. In high humidity or high tem- peratures, this will provide maximum efficiency. Turn ON the air conditioner early in the morning, to give it a head start on cooling. FIREPLAcE Please refer to the fireplace manual for operation, service and maintenance information.
  • Page 207: Slideout Systems

    20 6 s li d eo u T sYsTe Ms S L I D E O U T S Y S T E M S SLIDEOUT SYSTEMS BEFoRE operating your slideout system: • Check that you have sufficient power available. •...
  • Page 208: Hydraulic Slide-Out Manual Override

    Immediately clean any water puddles or debris brought inside your RV from slideout operation. Press and hold the appropriate slide room button to either IN or OUT, until the room is completely extended or retracted. • The galley and dinette slides are hydraulic. DO NOT hold these slide room buttons past the point the room is fully extended/retracted or damage may occur.
  • Page 209: Figure 117. Hydraulic Reservoir For Slides And Leveling

    20 8 s li d eo u T sYsTe Ms Figure 117. Hydraulic Reservoir for Slides and Leveling Under normal In normal operation, the galley and dinette slides are both operated using the single button on the Spyder touchpanel. The hydraulic slide bleed valves allow you to open up just one slide (as opposed to opening both at the same time) This is useful if you are in a tight parking lot and only have enough room to open a single side.
  • Page 210: Schwintek In-Wall Slideout System Manual Override

    s li d eo u T sYsTe Ms 20 9 NOTE: If your slideout system: • Stalls out before reaching end of stroke, or • Does NOT close and seal tightly. Contact your dealer or Vanleigh RV Customer Service for trouble shooting and/ or repair.
  • Page 211: Figure 119. Typical In-Wall Slide Controller

    2 10 s li d eo u T sYsTe Ms Figure 119. Typical In-Wall Slide Controller (Located in the front facing compartment of your fifth wheel) Electronic manual override (for board revision c1 and newer): Locate the circuit board. Press the MODE button six (6) times quickly, press a seventh (7 ) time and hold for approximately five (5) seconds.
  • Page 212: Troubleshooting The Schwintek In-Wall Slide System

    s li d eo u T sYsTe Ms 2 1 1 Disengage motors, manually retract room and travel lock: On the outside of the slide, Locate and remove motor retention screw located near the top of each vertical column on the side. Motor Retention Screw Slide Motor (Outside) Slide Motor (Inside)
  • Page 213: Table 22. Error Codes For The Schwintek In-Wall Slide System

    2 12 s li d eo u T sYsTe Ms • For error codes, the RED LED will blink between two and nine (2-9) times to indicate the error code (see below). Table 22. Error Codes for the Schwintek In-Wall Slide System red led error Code ...
  • Page 214 s li d eo u T sYsTe Ms 2 1 3 Non-moving side moved manually. • Try to push the non-moving side in and out. If a motor shaft has broken then it will be possible to move that side of the room several inches by hand. Larger rooms may require several people to push.
  • Page 215: Exterior Features

    2 14 e XT eri or f eaT ure s E X T E R I O R F E A T U R E S EXTERIoR LIGHTS Figure 121. Switch for Front Cap Light Figure 122. Porch Light Figure 123. Awning Light 2 1 4 VA N L E I G H B E A c o N...
  • Page 216: Roof & Ladder

    2 1 5 2 1 5 Figure 124. Motion Lights in Closets Ro oF & LADDER The RV is manufactured with a thermoplastic polyolefin (TPO) roof membrane, accessed by a ladder. Proper care and routine maintenance of your roof will assure many years of trouble-free performance.
  • Page 217: Awning

    2 16 e XT eri or f eaT ure s AWNING It is very important to keep your awning clean. The power patio awning is extremely dura- ble and can be operated during light rain and light wind conditions. However, when periods of heavy rain or wind are expected, the awning should be closed.
  • Page 218: Figure 127. Spyder System Awning Control

    e XT eri or f eaT ure s 2 1 7 Verify that the valance is in the correct orientation (see awning instructions found in the Owner’s Information Package). Allowing the valance to remain in a hyper extend- ed orientation may create a pooling water, especially in larger (17’-21’) awnings. Figure 127.
  • Page 219: Installing A Hitch Below The Bumper

    2 18 e XT eri or f eaT ure s closing the awning NOTE: Pinch Hazard – when closing the awning, the bottom arm will fold down and against the back channel. This area must be kept clear of people and objects. Failure to heed this warning could cause severe personal injury and/or property damage.
  • Page 220: Figure 130. Bolt-On Hitch

    e XT eri or f eaT ure s 2 1 9 NOTE: This hitch is not intended for towing a vehicle. Figure 130. Bolt-On Hitch VA N L E I G H B E A c o N 2 1 9...
  • Page 221: Interior Care

    2 20 i n T e rior Ca re I N T E R I O R C A R E cLEANING THE INTERIoR To keep the value of your RV, perform regular maintenance using the proper materials and procedures. •...
  • Page 222: Paneling

    2 2 1 2 2 1 PANELING • To clean, use a mild solution of soap and lukewarm water with a soft sponge or cloth. • Do not use abrasive cleaners as they could cause the vinyl to scratch and turn dull. •...
  • Page 223: Figure 131. Vinyl Tile

    2 2 2 i n T e rior Ca re important to remove loose soil and debris while it is on the surface. Heavily traveled areas (i.e., walkways, areas in front of the furniture) may be protected with small throw rugs to prolong the life of the carpet.
  • Page 224: Furniture Upholstery

    i n T e rior Ca re 2 2 3 Figure 132. Table and Chairs FURNITURE UPHoLSTERY To retain the value of your RV, maintain the furniture upholstery carefully and keep the interior clean. Vacuum the furniture regularly using a soft brush attachment to remove any loose dirt or debris.
  • Page 225: Recliner Sofa Or Loveseat

    2 2 4 i n T e rior Ca re REcLINER SoFA oR LoVESEAT Like a residential recliner, the recliner sofa or loveseat sections have controls allowing you to recline the individual sections. Contact Franklin Corporation for care instructions for this product.
  • Page 226: Abs Plastic

    i n T e rior Ca re 2 2 5 ABS PLASTIc ABS plastic components will retain their original beauty with reasonable care. Dust and wipe clean with soft, damp cloth or chamois, wiping gently. Do not use gritty or abrasive particle soaps or scouring compound to clean ABS plastic.
  • Page 227: Kitchen Sink

    2 2 6 i n T e rior Ca re cAUTIoN do noT oVereXTend THe sHade; THis Will daMage THe roller Tube. To oPeraTe THe sHades, Pull THe sHade doWn To THe desired leVel and sloWlY release To loCK THe sHade in PlaCe. To reTraCT, genTlY Pull doWn on THe sHade and release.
  • Page 228: Exterior Care

    eXT eri or Car e 2 2 7 E X T E R I O R C A R E The RV exterior is comprised of many different materials including; fiberglass gel-coat, au- tomotive grade paint finishes, plastics, glass, sealant, and aluminum. There is an increased chance of damage to the exterior finish, the longer a foreign sub- stance remains on the surface.
  • Page 229 2 2 8 eXT eri or Car e Vanleigh RV recommends the lambswool pad sold by Mary Moppins. This allows you to safely wash your RV from the ground by placing the pad on an extension. Do not mistake lambswool with imitations. Imitation pads are made from 100% polyester, which is plastic.
  • Page 230: Exterior Roof

    2 2 9 2 2 9 Salt and other chemicals spread on winter roads can have a detrimental effect on the RV’s underbody. If your RV is exposed to these conditions: • Wash the exterior of your RV. • Carefully spray the underbody with a high-pressure hose, remove any mud or debris that could trap and hold salt or moisture.
  • Page 231: Sidewall Vents

    2 3 0 eXT eri or Car e • If the loose sealant cannot be pulled off by hand, it still has good adhesion to the roof membrane and should be left alone. • Using a soft-bristled scrub brush, clean all areas to be resealed with a non-abrasive household cleaner or degreaser, such as Top Job or Spic-N-Span ®...
  • Page 232: Windows

    eXT eri or Car e 2 3 1 Figure 137. Exterior Appliance Doors WIND oWS Any ventilating window may permit water inside, especially during heavy rainstorms. Con- densation will also cause water to accumulate on windows and in the tracks. The window glass can be cleaned normally with a sponge and water.
  • Page 233: Doors

    2 32 eXT eri or Car e D o oRS The primary entrance door to the RV has a key lock and a dead bolt for additional security. When the door is fully opened, the door hinge automatically holds the door in an “open” position.
  • Page 234: Sealant

    eXT eri or Car e 2 33 Figure 140. Trailer Frame SEALANT Sealants perform a very important function and should be inspected closely and regularly maintained. Many different types of sealants are incorporated, including butyl/putty, black butyl-encapsulated foam, silicone (clear and colored), roof sealant and foam. In general, sealants do not have a “set”...
  • Page 235: Rv Storage

    2 3 4 eXT eri or Car e Figure 141. Roof Sealant RV SToRAGE Properly preparing your RV for storage during periods of non-usage will prevent problems from arising. It will also make it easier to get started again for the following camping trip or season.
  • Page 236: Suggested Maintenance Checklist

    eXT eri or Car e 2 3 5 Use the leveling legs during storage. Drain all water lines. Open the gate valves to flush the gray tank and black tank. Drain the freshwater tank. Open low point drains for the water heater. Flush the black tank.
  • Page 237 2 3 6 eXT eri or Car e Each Trip • Inspect and reseal as needed. • Check the auxiliary battery. Have the propane system checked for leaks by your dealer. • Check running lights. • Check tire pressure and wear, including spare. Make sure the tires are cold when check- ing the tire pressure.
  • Page 238: Basic Troubleshooting

    b a si C T rouble s Ho oTing 2 3 7 B A S I C T R O U B L E S H O O T I N G TROUBLESHO OTING, BASIC AIR coNDITIoNER (Ro oF) Will not operate •...
  • Page 239: Batteries

    2 3 8 b a si C T rouble s Ho oTing BATTERIES Batteries are dead when the RV is coming out of storage The batteries are dead because the hydraulic pump asks to remain energized, thus taking power from the batteries. Additionally, this is also true of any appliance in the coach with an internal clock.
  • Page 240: Interior Lights

    2 39 2 39 • Inspect exhaust tube for any obstructions. • Check furnace fuse in fuse panel. Replace if necessary. • Check that the return air grill is unobstructed. Remove anything that is stored in the furnace compartment that could block airflow. •...
  • Page 241: Microwave

    2 40 b a si C T rouble s Ho oTing 10A Fuse Resettable Breakers Figure 142. 10A Fuse and Resettable Breakers for Jacks/Leveling System overriding Use of the Hydraulic Legs WARNING in THe eVenT THaT Your HYdrauliC leVeling legs beCoMe sTuCK or oTHerWise inoPerable, aTTeMPTing To forCe or ManuallY oVerride THe legs Yourself is boTH noT reCoMMended and Can be HaZardous To Your rV.
  • Page 242: Outside Receptacle

    b a si C T rouble s Ho oTing 2 41 • Make sure the GFCI is not tripped. • Door open or timer OFF. Close door and turn ON timer. • Call Tech Support if no resolution. oUTSIDE REcEPTAcLE No power to outside receptacle •...
  • Page 243: Portable Generator (Customer Supplied)

    2 42 b a si C T rouble s Ho oTing P oRTABLE GENERAToR (cUSToMER SUPPLIED) Starter engages while holding the start button down, but generator does not start • Generator may be out of fuel. (Generator will not operate when the fuel tank is less than ¼...
  • Page 244: Refrigerator

    b a si C T rouble s Ho oTing DANGER failure To CoMPlY Could resulT in eXPlosion resulTing in deaTH or serious inJurY. REFRIGERAToR The control panel lights are not illuminated • Check coach circuit breakers and GFCI receptacle. • Verify that refrigerator is plugged into the 120-volt outlet.
  • Page 245: Schwintek Electric Slideouts

    2 4 4 b a si C T rouble s Ho oTing Figure 143. Running Lights Fuse ScHWINTEK ELEcTRIc SLIDEoUTS Room moves in and out very slowly, binds or squeaks • Lubricate the slide-out tubes and rollers with light spray lube. Figure 144.
  • Page 246: Tv Antenna

    b a si C T rouble s Ho oTing Water is getting in at the bottom corners of the room • Verify exterior seals are against the room at the top corners and not turned in when the room is out (horizontal seal overlaps vertical). Also, check for voids in the seal on the slide roof and side panels.
  • Page 247: Water Heater

    2 46 b a si C T rouble s Ho oTing WATER HEATER Temperature-pressure relief valve weeping • Weeping or dripping of relief valve while water heater is running does NOT mean it is faulty. There is an odor that smells like rotten eggs •...
  • Page 248: Water Pump

    b a si C T rouble s Ho oTing 2 47 Continue this flushing process for approximately five (5) minutes allowing ample time for the fresh water to agitate the stagnant water on the bottom of the tank and force the deposits through the drain opening. Upon completion of the steps above, close the drain plug as well as the relief valve.
  • Page 249: Water System

    2 48 b a si C T rouble s Ho oTing • Check plumbing for leaks and inspect for leaky valves on toilet. • Have the pump checked by your dealer or a qualified RV technician. WATER SYSTEM Wet areas near water connections, pump runs while the faucets are closed, and no other fresh water fixtures are being used •...
  • Page 250: Maintenance Data And Charts

    Ma in T e n a n Ce daTa and CHa r Ts 2 49 M A I N T E N A N C E D A T A A N D C H A R T S RV oWNER’S DATA SHEET The following is a table to for you to keep better records of your appliances, etc.: Some items may be optional equipment.
  • Page 251: Rv Owner's Maintenance Record

    2 50 Ma in T e n a n Ce daTa and CHar Ts RV oWNER’S MAINTENANcE REcoRD The following is a table to for you to keep better records of maintenance on your RV: Appliance Brand Model Number Serial Number 2 5 0 VA N L E I G H B E A c o N...
  • Page 252: Glossary

    2 51 2 51 G L O S S A R Y Ac ELEcTRIcITY — Alternating current also known as shoreline power. For purposes of this manual, it refers to 120-volt AC (abbreviated 120 VAC). AMP — Short for ampere, the electric current unit of measure. RV sites with electric hookup will specify the maxi-mum amps supported, which generally come in units of 20, 30, or 50 amps.
  • Page 253 2 52 g lo ssa r Y BRITISH THERMAL UNIT (BTU) — Measurement of heat that is the quantity required to raise the temperature of one pound of water 1°F. RV air-conditioners and furnaces are BTU-rated. cAMBER (WHEEL ALIGNMENT) — The number of degrees each wheel is off of vertical. Looking from the front, tops of wheels farther apart than bottoms means “positive camber”.
  • Page 254 2 5 3 2 5 3 cURB WEIGHT —The actual weight of a vehicle or trailer, including all standard equip- ment, full fuel tanks, full fresh water tanks, full propane bottles, and all other equipment fluids, but before taking on any persons or personal cargo. cURBSIDE —...
  • Page 255 2 5 4 g lo ssa r Y DUMP STATIoN — Site where you drain your gray water (waste) and your black water (sew- age) tanks. In most states, it is illegal to drain your tanks anywhere except dump stations. DUMP VALVE —...
  • Page 256 g lo ssa r Y 2 55 GRoSS AXLE WEIGHT RATING (GAWR) — The MAXIMUM ALLOWABLE WEIGHT each axle assembly is designed to carry, as measured at the tires, therefore including the weight of the axle assembly itself. GAWR is established by considering the rating of each of its components (tires, wheels, springs, axle), and rating the axle on its weakest link.
  • Page 257 2 56 g lo ssa r Y HoLDING TANKS — There are three different holding tanks on most RVs; fresh water tank, gray water tank and black water tank. The fresh water tank holds fresh water that can be stored for later use. The gray water tank holds the waste water from the sinks and showers. The black water tank holds the waste from the toilet.
  • Page 258 g lo ssa r Y 2 5 7 hitch or extended fifth wheel pin box can result in damage to the truck cab or breaking out the back window of the truck cab from the truck and fifth wheel “colliding”. KING PIN —...
  • Page 259 2 5 8 g lo ssa r Y PARK MoDEL — A travel trailer that requires park facilities to function. It lacks holding tanks and dual-voltage appliances, requiring to be plugged into water, sewage, and electri- cal facilities. A park model is more of a small mobile home than a recreational vehicle, in appearance and function.
  • Page 260 g lo ssa r Y Ro oF AIR coNDITIoNING — Air conditioning unit mounted on roof of RV, to cool the RV when it is parked. When moving, most RVs are cooled by separate air conditioning units which are components of the engine, or they may be cooled by a roof top if a proper size generator is installed.
  • Page 261 2 60 g lo ssa r Y THERMo coUPLE — A thermocouple is a device that monitors the pilot flame of a pilot model propane appliance. If the pilot flame is extinguished the thermocouple causes the gas valve to shut off the flow of gas to both the pilot flame and the main burner. TIP oUT —...
  • Page 262 g lo ssa r Y 2 6 1 cedures, tire manufacturers perform their own evaluations for these characteristics. Each manufacturer then labels the tire, according to grade. UV DEGRADATIoN — A breaking down of material due to the sun’s harsh ultraviolet rays. UNLoADED VEHIcLE WEIGHT (UVW) —...
  • Page 263 2 62 g lo ssa r Y YAW — Fishtailing action of the trailer caused by external forces that set the trailer’s mass into a lateral (side-to-side) motion. The trailer’s wheels serve as the axis or pivot point. Also known as “sway.” 2 6 2 VA N L E I G H B E A c o N...
  • Page 264 26 3 26 3 I N D E X 7-Way Wire Harness/Connector Plug 12-Volt DC System 12- Volt Fuse Panel 12V USB Receptacles 120-Volt AC System 120-Volt AC (VAC) Receptacles 120-Volt Circuit Breakers ABS Plastic Air Conditioner (Roof) Air Conditioning Approximate Electrical Load Ratings Audio/Visual System Guide Automatic Leveling System...
  • Page 265 2 6 4 i nde X Dewinterizing Doors Draining the Fresh Water System Drain Pipes With HEPVO Valve Drain Pipes With P-Traps Ducting & Return Air Electrical Electrical Power - 110 V Emergency Egress Window Emergency Weather Planning Emptying The Black & Gray Water Tanks Exterior Lights Exterior Roof Family Safety Plan...
  • Page 266 i nde X 2 65 Oven Pet Safety Propane Alarm Propane Gas System Propane Regulator Propane System Hoses, Tubes, Pipes & Fittings Range Hood Recommended Practices Refrigerator Refrigerator Roof & Ladder Roof Vent/Fans Running Lights RV Owner’s Data Sheet RV Owner’s Maintenance Record RV Storage Sanitizing the Fresh Water System Satellite Prep...
  • Page 267 2 66 i nde X Trailer Frame Transfer Switch Troubleshooting, Basic TV Antenna TV Roof Antenna UNV (Unloaded Vehicle Weight) Vents & Vent Pipes Warranty, (3) Three Year Limited Structural Warranty Service Water Control System Water Heater Water Heater Draining and Winterization Water Pump Water System Weighing Your Tow Vehicle &...
  • Page 268 B U I L T A R O U N D Y O U 26 Industrial Drive Access Road Burnsville, MS 38833 Phone: 662.612.4040 Fax: 662.655.0913 vanleighrv.com...

Table of Contents