Lmt (Servo Maximum Travel Limit - All Model Types) - AIRTRONICS SD-10G Operating Manual

surface MENU
The tables below show the End Point Adjustment travel direction options for the Default channel for each Model Type.
Channels will vary based on current Model Type and specific Model Type selection options. End Point Adjustment values
for the Flap channel and the Auxiliary channels can be set individually for all three Switch Positions.
DEFAULT CHANNEL
CH01
CH02
CH03
CH04
CH05
U/D = Up/Down L/R = Left/Right L*/H = Low/High R/L = Right/Left
IMPORTANT In front of each EPA Adjustment Value is a specific icon. To set the EPA Adjustment Value for the desired
direction of servo travel, the control stick or switch must be moved in the direction of servo travel you want to change the EPA
Adjustment Value for. For example, if you want to change the EPA Adjustment Value for Down elevator, push the elevator
control stick forward, then release it. 'D' will be displayed in front of the EL EPA Adjustment Value.
Changing End Point Adjustment Values
1) Press the Navigation Pad 3456 to highlight the EPA Adjustment
Value for the channel that you would like to change.
2) Move the control stick or switch in the direction of servo travel you would
like to change the EPA Adjustment Value for, then press the YES/+ or
NO/- keys to change the EPA Adjustment Value.
3) Adjust the desired remaining EPA Adjustment Values using the same
techniques.
EPA setting range for the primary flight controls is 0% to 150%. The default setting is 100%. EPA setting range for Flaps and
Auxiliary channels is -150% to 150%. The default setting range varies based on current Model Type and specific Model
Type selection options, and the positions of the Flap and Auxiliary channel switches. Increasing the EPA Adjustment Value
increases servo travel and decreasing the EPA Adjustment Value decreases servo travel.
LiMT (SERvO MaxiMUM TRavEL LiMiT - aLL MODEL TYpES)
The Limits function allows you to set a hard limit for servo travel in each direction (H - High or L - Low). This means that
regardless of the End Point Adjustment, Dual Rate, and/or Mixing Adjustment Values programmed, the servo will never rotate past
the specified Limits. Limits should be used to Limit the maximum required physical travel of the servo in each direction, so that the
servo can never rotate further than intended. For example, if when you set up your model the elevator control linkage binds when
full elevator control is commanded, use the Limits function to decrease the servo travel and prevent binding. Another example
is with the use of flaps and a mixing function that utilizes flaps. Under no circumstances would you want the flaps to move up. In
this situation, you can use the Limits function to set the flap Up servo travel to zero. With this setting there would be no way for
the flaps to move up since the servo travel Limit in that direction is zero.
Changing Limit Adjustment Values - High
1) Press the Navigation Pad 3456 to highlight the LIMT H Adjustment
Value for the channel that you would like to change.
2) Press the YES/+ or NO/- keys to change the LIMT H Adjustment Value.
3) Adjust the desired remaining LMT H Adjustment Values using the same
techniques.
LIMT H setting range is 0% to 150%. The default setting is 150%. Increasing the LIMT H Adjustment Value increases the servo
travel High-side Limit and decreasing the LIMT H Adjustment Value decreases the servo travel High-side Limit.
AERO GLID HELI
U/D U/D U/D
L/R L/R L/R
L*/H L*/H L*/H
R/L R/L L/R
L*/H L*/H ---
Page 66
DEFAULT CHANNEL
CH06
CH07
CH08
CH09
CH10
N/1/2 = Neutral/Position 1/Position 2 L*/N/H = Low/Neutral/High
AERO GLID HELI
N/1/2 L/R L*/H
L*/N/H N/1/2 ---
L*/N/H L*/N/H L*/N/H
L*/N/H L*/N/H L*/N/H
L*/N/H L*/N/H L*/N/H