YASKAWA iQpump1000 Installation & Start?Up Manual page 60

i.5 Start-Up Programming and Operation
Setting
13 Reverse Jog
14 Fault reset
15 Fast Stop (N.O.)
17 Fast Stop (N.C.)
18 Timer function input
19 PID disable
1A Accel/decel time selection 2
1B Program lockout
1E Reference sample hold
20 to 2F Ext. pump fault
30 PID integral reset
31 PID integral hold
Multi-Step Speed
32
Reference 4
34 PID soft starter cancel
35 PID input level selection
Forward run command
40
(2-Wire sequence)
Reverse run command
41
(2-Wire sequence)
Run command
42
(2-Wire sequence 2)
FWD/REV command
43
(2-Wire sequence 2)
47 Node setup
51 Sequence Timer Disable
52 Sequence Timer Cancel
60 DC Injection Braking command
External Speed Search
61
command 1
External Speed Search
62
command 2
63 Field weakening
65 KEB Ride-Thru 1 (N.C.)
66 KEB Ride-Thru 1 (N.O.)
<1> Available in drive software versions PRG: 8552 and later.
Not available in drive models 4A0930 and 4A1200.
n H2-01 to H2-03: Terminal M1-M2, M3-M4, and MD-ME-MF Function Selection
The drive has three multi-function output terminals.
H2-02, and H2-03.
No.
H2-01
H2-02
H2-03 Terminal MD-ME-MF Function Selection (relay)
<1> Default is F: Through Mode in drive software versions PRG: 8551 and earlier.
Setting
0 During run
1 Zero speed
2 Speed agree 1
3 User-set speed agree 1
60
Function
Parameter Name
Terminal M1-M2 Function Selection (relay)
Terminal M3-M4 Function Selection (relay)
Table i.23 Multi-Function Digital Output Terminal Settings
Function
Page Setting
– 67 Communications test mode
– 68 High Slip Braking (HSB)
– 6A Drive enable
– 73 Low City Press
– 75 Up 2 command
– 76 Down 2 command
– 7A KEB Ride-Thru 2 (N.C.)
– 7B KEB Ride-Thru 2 (N.O.)
– 80 HAND Mode
– 81 HAND Mode 2
– <1>
PI Switch to Aux
82
–
83 Alternate Multi-Setpoint (Q1-02)
84 Alternate Multi-Setpoint (Q1-03)
–
85 Alternate Multi-Setpoint (Q1-04)
–
88 Volute-Thermostat Normally Open
–
89 Volute-Thermostat Normally Closed
–
8C Disable Pre-Charge
8D Multi Setpoint 1
–
8E Multi Setpoint 2
8F Low Water Level
–
90 High Water Level
–
92 Reset Accum
95 Remove Drive Disable
–
A8 Secondary PI Disable (N.O.)
–
A9 Secondary PI Disable (N.C.)
–
AA Secondary PI Inverse Operation
–
AB Secondary PI Integral Reset
–
AC Secondary PI Integral Hold
AD Select Secondary PI Parameters
–
AF Emergency Override Forward Run
–
B0 Emergency Override Reverse Run
–
–
Table i.23 lists the functions available for these terminals using H2-01,
Page Setting
– 4 Frequency detection 1
– 5 Frequency detection 2
– 6 Drive ready
– 7 DC bus undervoltage
YASKAWA TOEP YAIP1W 02E YASKAWA AC Drive - iQpump1000 Installation & Start-up Guide
Function
Setting Range
0 to 192 37: During Frequency Output
0 to 192
42: Pressure Reached
0 to 192
Function
Page
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Default
<1>
E: Fault
Page
–
–
–
–