YASKAWA iQpump1000 Installation & Start?Up Manual page 61

Setting
8 During baseblock (N.O.)
9 Frequency reference source
A Run command source
A HAND Mode
B Torque detection 1 (N.O.)
C Frequency reference loss
<1>
Braking resistor fault
D
E Fault
F Through mode
10 Minor fault
11 Fault reset command active
12 Timer output
13 Speed agree 2
14 User-set speed agree 2
15 Frequency detection 3
16 Frequency detection 4
17 Torque detection 1 (N.C.)
18 Torque detection 2 (N.O.)
19 Torque detection 2 (N.C.)
1A During reverse
1B During baseblock (N.C.)
1E Restart enabled
1F Motor overload alarm (oL1)
20 Drive overheat pre-alarm (oH)
22 Mechanical weakening detection
2F Maintenance period
30 During torque limit
37 During frequency output
38 Drive enabled
39 Watt hour pulse output
3D During speed search
3E PID feedback low
3F PID feedback high
40 Auto Mode
42 Pressure Reached
43 2 Motor Alternate
4A During KEB Ride-Thru
4C During fast stop
4D oH Pre-alarm time limit
<2>
Braking transistor fault (rr)
4E
<2>
Braking resistor overheat (oH)
4F
51 Sequence timer 1
<1> Not available in models 4A0930 and 4A1200.
<2> Not available in models 2A0169 to 2A0415 and 4A0088 to 4A1200.
Setting 30: During Torque Limit
The output closes when the motor is operating at the torque limit specified by the L7-oo parameters or an analog input. This
setting can only be used in OLV control mode.
Setting 42: Pressure Reached
Note: 1. Setting available in drive software versions PRG: 8552 and later.
2. Setting not available in drive models 4A0930 and 4A1200.
YASKAWA TOEP YAIP1W 02E YASKAWA AC Drive - iQpump1000 Installation & Start-up Guide
Function
i.5 Start-Up Programming and Operation
Page Setting
– 52 Sequence timer 2
– 53 Sequence timer 3
– 54 Sequence timer 4
– 58 Underload detection
– 60 Internal cooling fan alarm
– 71 Secondary PI Feedback Low
72 Secondary PI Feedback High
–
80 Pump 2 Control
–
81 Pump 3 Control
–
82 Pump 4 Control
–
83 Pump 5 Control
–
84 Pump 6 Control
–
89 Output 1 Limit
–
8B Lube Pump or Digital Output Delay
–
8F Internal Fan On
–
91 Pump Fault
–
92 Transducer Loss
–
93 Setptoint Not Met
94 Loss of Prime
–
95 Volute Thermostat Fault
–
96 High Feedback
–
97 Low Feedback
–
98 Low Flow
–
99 Accum Level
–
9A High Flow
–
9B Low Water Level
–
9C Low Suction
61
9D High Suction
–
9E Low PI Aux Level
–
9F High PI Aux Level
–
A0 Water Loss/Suction Pressure/PI Aux Control
–
A1 Differential Detected
–
A2 Sleep Active
–
A3 Start Delay
–
A4 Pre-Charge
61
A5 Anti-Jam Active
–
A6 De-Scale Active
–
A7 Flow Rate Limit
–
A9 Thrust Mode
–
AA Utility Start Delay
–
100 to
–
Function 0 to AA with inverse output
1AA
–
Function Page
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
61