D-Link DSR-150 User Manual page 353

Appendix D - Log Output Reference
%s: unable to reset hardware; hal status %u,
__func__, status
****ASSERTION HIT****
MacAddr=%s,
TxBufIdx=%d, i
Tid=%d, tidno
AthBuf=%p, tid->tx_buf[i]
%s: unable to reset hardware; hal status %u,
%s: unable to reset hardware; hal status %u,
%s: unable to start recv logic,
_fmt, __VA_ARGS__ \
sample_pri=%d is a multiple of refpri=%d,
sample_pri, refpri
===========ft->ft_
numfilters=%u===========, ft->ft_numfilters
filter[%d] filterID = %d rf_numpulses=%u;
rf->rf_minpri=%u; rf->rf_maxpri=%u; rf-
>rf_threshold=%u; rf->rf_filterlen=%u; rf->rf_
mindur=%u; rf->rf_maxdur=%u,j, rf->rf_pulseid,
NOL
WARNING!!! 10 minute CAC period as channel is a
weather radar channel
%s disable detects, __func__
%s enable detects, __func__
%s disable FFT val=0x%x , __func__, val
%s enable FFT val=0x%x , __func__, val
%s debug level now = 0x%x , __func__, dfs_
debug_level
RateTable:%d, maxvalidrate:%d, ratemax:%d,
pRc->rateTableSize,k,pRc->rateMaxPhy
%s: txRate value of 0x%x is bad., __FUNCTION__,
txRate
Valid Rate Table:-
Index:%d, value:%d, code:%x, rate:%d, flag:%x, i,
(int)validRateIndex[i],
RateTable:%d, maxvalidrate:%d, ratemax:%d,
pRc->rateTableSize,k,pRc->rateMaxPhy
Can't allocate memory for ath_vap.
Unable to add an interface for ath_dev.
%s: [%02u] %-7s , tag, ix, ciphers[hk->kv_type]
%02x, hk->kv_val[i]
mac %02x-%02x-%02x-%02x-%02x-%02x,
mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]
D-Link DSR-Series User Manual
DEBUG %s: failed to allocate descriptors: %d,
%s: unable to setup a beacon xmit
DEBUG
queue!,
DEBUG %s: unable to setup CAB xmit queue!,
%s: unable to setup xmit queue for %s
DEBUG
traffic!,
%s: unable to register device, dev-
DEBUG
>name
DEBUG %s: autocreation of VAP failed: %d,
ath_dev_probe: no memory for device
DEBUG
state
kdot11RogueAPEnable called with
DEBUG
NULL argument.
kdot11RogueAPEnable: can not add
DEBUG
more interfaces
kdot11RogueAPGetState called with
DEBUG
NULL argument.
kdot11RogueAPDisable called with
DEBUG
NULL argument.
%s: SKB does not exist., __
DEBUG
FUNCTION__
DEBUG %s: recvd invalid skb
DEBUG unable to register KIFDEV to UMI
The system is going to factory
DEBUG
defaults........!!!
DEBUG %s, msg
DEBUG %02x, *(data + i)
DEBUG Inside crypt_open in driver ######
DEBUG Inside crypt_release in driver ######
Inside crypt_init module in driver
DEBUG
@@@@@@@@
Inside crypt_cleanup module in driver
DEBUG
@@@@@@@@
DEBUG SKB is null : %p ,skb
DEBUG DST is null : %p ,dst
DEBUG DEV is null %p %p ,dev,dst
Packet is Fragmented %d,pBufMgr-
DEBUG
>len
Marked the packet proto:%d
DEBUG sip:%x dip:%x sport:%d dport:%d
spi:%d,isr:%p:%p %p
DEBUG SAV CHECK FAILED IN DECRYPTION
DEBUG FAST PATH Breaks on BUF CHECK
DEBUG FAST PATH Breaks on DST CHECK
FAST PATH Breaks on MTU %d %d
DEBUG %d,bufMgrLen(pBufMgr),mtu,dst_
mtu(pDst->path)
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
ERROR
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
CRITICAL
339