Danfoss VLT AutomationDrive FC 360 Quick Manual page 52

Specifications
Frequency converter typical
shaft output [kW]
Enclosure protection rating
IP20
Output current
Continuous (3x380–440 V)
[A]
Continuous (3x441–480 V)
[A]
Intermittent (60 s overload)
[A]
Continuous kVA (400 V AC)
[kVA]
Continuous kVA (480 V AC)
[kVA]
Maximum input current
Continuous (3x380–440 V)
[A]
Continuous (3x441–480 V)
[A]
8 8
Intermittent (60 s overload)
[A]
Additional specifications
Maximum cable size (mains,
motor, brake) [mm
Estimated power loss at
rated maximum load [W]
Weight [kg], enclosure
protection rating IP20
Efficiency [%] 3)
Table 8.3 Mains Supply 3x380–480 V AC - Normal Duty
1) Heavy duty=150–160% current during 60 s, Normal duty=110% current during 60 s.
2) The typical power loss is at nominal load conditions and expected to be within
cable conditions).
Values are based on a typical motor efficiency (IE2/IE3 border line). Motors with lower efficiency add to the power loss in the frequency
converter and motors with high efficiency reduce power loss.
Applies for dimensioning of frequency converter cooling. If the switching frequency is higher than the default setting, the power losses
may rise. LCP and typical control card power consumptions are included. Further options and customer load may add up to 30 W to the
losses (though typical only 4 W extra for a fully loaded control card, fieldbus, or options for slot B).
For power loss data according to EN 50598-2, refer to www.danfoss.com/vltenergyefficiency.
3) Measured using 5 m screened motor cables at rated load and rated frequency for enclosure sizes J1–J5, and using 33 m screened
motor cables at rated load and rated frequency for enclosure sizes J6 and J7. For energy efficiency class, see the Ambient Conditions
section in chapter 8.2 General Technical Data. For part load losses, see www.danfoss.com/vltenergyefficiency.
50
VLT
Q11K Q15K
11 15
J4 J4
23 31
21 27
25.3 34.1
15.94 21.48
17.5 22.4
22.1 29.9
18.4 24.7
24.3 32.9
2 (AWG)]
289.53 393.36
2)
9.4 9.5
97.8 97.8
Danfoss A/S © 04/2015 All rights reserved.
®
AutomationDrive FC 360
Q18K Q22K Q30K
18.5 22 30
J5 J5
37 42.5
34 40
40.7 46.8 67.1
25.64 29.45 42.3
28.3 33.3 43.2
35.2 41.5
29.3 34.6 49.3
38.7 45.7 62.7
16(6)
402.83 467.52 630
12.3 12.5 22.4
98.1 97.9 98.1
1)
Q37K Q45K
37 45
J6 J6 J6
61 73 90
52 65 77
80.3 99
50.6 62.4
54.0 64.0
57 70.3 84.2
60.8 72.7
77.3 92.6
50(1/0)
848 1175
22.5 22.6
98.0 97.7
± 15% (tolerance relates to variety in voltage and
Q55K Q75K
55 75
J7 J7
106 147
96 124
116.6 161.7
73.4 101.8
79.8 103.1
102.9 140.3
88.8 121.1
113.2 154.3
85(3/0)
1250 1507
37.3 38.7
98.0 98.2
MG06A602