Base Plate Dimensions; Accessory For Mounting; Figure 52. M8 Sensor Mounting Drawing Of Rectangular Base Plate; Figure 53. M8 Sensor Adjustable Mount Accessory - quanergy M8 User Manual

4

Base Plate Dimensions

When attached to the sensor, the rectangular base plate's four M3 threaded corner holes
are used to mount securely to a surface.
B
1/4-20 TAPPED THRU
54.00
40.00
25.80
4.98 TYP.
0
25.80
40.00
54.00

Accessory for Mounting

Some implementations of the M8 sensor are easier to achieve with the specialized
NOTES:
1) STAMP/SCRIBE THE QUANERGY PART WITH PN, 4X-XXXXX, AND SITE-DATE CODE, XXXXXX. FOR
Adjustable Mount accessory available for purchase from Quanergy. This accessory attaches
THE SITE DATE-DATE CODE INSTRUCTIONS SEE THE DOCUMENT 98-00012. USE A FONT SIMILAR TO
ARIAL 10.
to either a flat surface or a pole, and it adjusts for roll and pitch, as explained on page 80.
2) MATERIAL: 6061 ALUM.
3) FINISH: BLACK ANODIZED.
4) ALL OTHER DIMENSIONS TO BE TAKEN FROM SOLID MODEL WITH LATEST REVISION.
5) BREAK ALL SHARP EDGES
4
Back Plate
Pole Clamp
Strapping Slot (4X)
Roll Adjuster
Roll Plate
Roll Dots
in 5° Increments
STANDARD TRIPOD HOLE
1

Figure 52. M8 Sensor Mounting Drawing of Rectangular Base Plate

8
D
C
B
A

Figure 53. M8 Sensor Adjustable Mount Accessory

8
3
12.7
R10.00
TYP.
0.25
8X 5.0mm THRU
9.53 4.8 DP.
4X EACH SIDE
AS SHOWN
6
7
3
7 6
M8 Sensor User Guide, QPN 96-00001 Rev K
2
22.0
10.00
46.50
5 4
REV
PROPRIETARY AND CONFIDENTIAL
THIS DOCUMENT IS THE PROPERTY OF QUANERGY SYSTEMS
INC. AND CONTAINS INFORMATION WHICH IS CONFIDENTIAL
AND PROPRIETARY TO QUANERGY SYSTEMS INC. NO PART
OF THIS DOCUMENT MAY BE COPIED, REPRODUCED OR
DISCLOSED TO THIRD PARTIES WITHOUT THE WRITTEN
CONSENT OF QUANERGY SYSTEMS INC.
2
Pitch Plate
Pitch Dots
in 5° Increments
Pitch Adjuster
Mounting Hole (4X)
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MM
TOLERANCES:
DECIMALS ANGLES
.X = .25
.XX = .10
.XXX = .05
THIRD ANGLE PROJECTION
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
MATERIAL
SEE NOTE
DRAWING IS THE SOLE PROPERTY OF
QUANERGY SYSTEMS INC. ANY
FINISH
REPRODUCTION IN PART OR AS A WHOLE
SEE NOTE
WITHOUT THE WRITTEN PERMISSION OF
QUANERGY SYSTEMS INC IS
DO NOT SCALE DRAWING
PROHIBITED.
5 4
REV DESCRIPTION
A Initial Release
B
Deleted Two Holes
C Cut-Out for Labe
Length was
D increased to
108mm
32.0 R1.50
LABEL
AREA
3 2
DESCRIPTION
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MM
DECIMALS: ANGLES:
.X= .25 0.5 DEGREES
.XX= .10
.XXX= .05
SIZE
B
DO NOT SCALE DRAWING
MATERIAL: FINISH:
SEE NOTES SEE NOTES
ORIGINATED BY: DATE
NAME DATE
H.E. 08/01/17
DRAWN
CHECKED
.5 DEGREES
ENG APPR.
TITLE:
MFG APPR.
FLEXMOUNT ISO
Q.A.
COMMENTS:
SIZE DWG. NO.
B
XXXXXXX
SCALE: 1:2
3 2
Page 78
1
BY
TITLE:
RECTA
BASE M
D
40
SCALE: N/A
Quanergy Systems
265 Sobrante Way,
Sunnyvale, CA 9408
SHE
1