YOKOGAWA WT310EH User Manual page 54

6.7 INPut Group
Description In the parameters, list the external current sensor
ranges that you want to enable. To enable all the
ranges, specify the parameter "ALL."
[:INPut]:CURRent:EXTSensor:POJump
Function Sets or queries the jump destination range that is
used when a current peak over-range occurs.
Syntax
[:INPut]:CURRent:EXTSensor:POJump
{OFF|< Voltage >}
[:INPut]:CURRent:EXTSensor:POJump?
OFF = No jump destination current range
<Voltage> = See ( :INPut:CURRent:
RANGe ).
Example
:INPUT:CURRENT:EXTSENSOR:POJUMP 2V
:INPUT:CURRENT:EXTSENSOR:POJUMP?
-> :INPUT:CURRENT:EXTSENSOR:POJUMP
2.00E+00
[:INPut]:CURRent:SRATio?
Function Queries the external current sensor conversion
ratios of all elements.
Syntax
[:INPut]:CURRent:SRATio?
Description This command is only valid on models with the
external current sensor input (/EX1 or /EX2)
option.
[:INPut]:CURRent:SRATio[:ALL]
Function Collectively sets the external current sensor
conversion ratios of all elements.
Syntax
[:INPut]:CURRent:SRATio[:ALL]
{<NRf>}
<NRf> = 0.001 to 9999.
Example :INPUT:CURRENT:SRATIO:ALL 10
[:INPut]:CURRent:SRATio:ELEMent<x>
Function Sets or queries the external current sensor
conversion ratio of the specified element.
Syntax
[:INPut]:CURRent:SRATio:ELEMent<x>
{<NRf>}
[:INPut]:CURRent:SRATio:ELEMent<x>?
<x> = 1 to 3 (element)
<NRf> = 0.001 to 9999.
Example :INPUT:CURRENT:SRATIO:ELEMENT1 10
:INPUT:CURRENT:SRATIO:ELEMENT1?
-> :INPUT:CURRENT:SRATIO:ELEMENT1
10.00
[:INPut]:RCONfig
Function Sets or queries the on/off state of the range
configuration (valid range selection) feature.
Syntax
[:INPut]:RCONfig {<Boolean>}
[:INPut]:RCONfig?
Example
:INPUT:RCONFIG OFF
:INPUT:RCONFIG? -> :INPUT:RCONFIG 0
6-14
Description The following commands are enabled only when
this command is set to ON. Measurement range
can be skipped.
:INPut:VOLTage:CONFig
:INPut:VOLTage:POJump
:INPut:CURRent:CONFig
:INPut:CURRent:POJump
:INPut:CURRent:EXTSensor:CONFig
:INPut:CURRent:EXTSensor:POJump
[:INPut]:SCALing?
Function Queries all scaling settings.
Syntax
[:INPut]:SCALing?
[:INPut]:SCALing[:STATe]
Function Sets or queries the scaling on/off state.
Syntax
[:INPut]:SCALing[:STATe] {<Boolean>}
[:INPut]:SCALing:STATe?
Example :INPUT:SCALING:STATE OFF
:INPUT:SCALING:STATE?
-> :INPUT:SCALING:STATE 0
[:INPut]:SCALing:{VT|CT|SFACtor}?
Function Queries the VT ratios, CT ratios, or power
coefficients of all elements.
Syntax
[:INPut]:SCALing:{VT|CT|SFACtor}?
[:INPut]:SCALing:{VT|CT|SFACtor}
[:ALL]
Function Collectively sets the VT ratio, CT ratio, or power
coefficient of all elements.
Syntax
[:INPut]:SCALing:{VT|CT|SFACtor}
[:ALL] {<NRf>}
<NRf> = 0.001 to 9999.
Example :INPUT:SCALING:VT:ALL 1
[:INPut]:SCALing:{VT|CT|SFACtor}:
ELEMent<x>
Function Sets or queries the VT ratio, CT ratio, or power
coefficient of the specified element.
Syntax
[:INPut]:SCALing:{VT|CT|SFACtor}
:ELEMent<x> {<NRf>}
[:INPut]:SCALing:{VT|CT|SFACtor}
:ELEMent<x>?
<x> = 1 to 3 (element)
<NRf> = 0.001 to 9999.
Example
:INPUT:SCALING:VT:ELEMENT1 1
:INPUT:SCALING:VT:ELEMENT1?
-> :INPUT:SCALING:VT:ELEMENT1 1.000
[:INPut]:SYNChronize
Function Sets or queries the synchronization source.
Syntax
[:INPut]:SYNChronize
{VOLTage|CURRent|OFF}
[:INPut]:SYNChronize?
Example :INPUT:SYNCHRONIZE VOLTAGE
:INPUT:SYNCHRONIZE?
-> :INPUT:SYNCHRONIZE VOLTAGE
IM WT310E-17EN