YOKOGAWA WT310EH User Manual page 42

6.1 List of Commands
Command
[:INPut]:VOLTage:POJump
[:INPut]:CURRent?
[:INPut]:CURRent:RANGe
[:INPut]:CURRent:AUTO
[:INPut]:CURRent:CONFig
[:INPut]:CURRent:POJump
[:INPut]:CURRent:EXTSensor:
CONFig
[:INPut]:CURRent:EXTSensor:
POJump
[:INPut]:CURRent:SRATio?
[:INPut]:CURRent:SRATio[:ALL]
[:INPut]:CURRent:SRATio:
ELEMent<x>
[:INPut]:RCONfig
[:INPut]:SCALing?
[:INPut]:SCALing[:STATe]
[:INPut]:
SCALing:{VT|CT|SFACtor}?
[:INPut]:
SCALing:{VT|CT|SFACtor}[:ALL]
[:INPut]:
SCALing:{VT|CT|SFACtor}:
ELEMent<x>
[:INPut]:SYNChronize
[:INPut]:FILTer?
[:INPut]:FILTer:LINE
[:INPut]:FILTer:FREQuency
[:INPut]:POVer?
[:INPut]:CRANge?
INTEGrate Group
:INTEGrate?
:INTEGrate:MODE
:INTEGrate:TIMer
:INTEGrate:STARt
:INTEGrate:STOP
:INTEGrate:RESet
:INTEGrate:STATe?
MATH Group
:MATH
MEASure Group
:MEASure?
:MEASure:AVERaging?
:MEASure:AVERaging[:STATe]
:MEASure:AVERaging:TYPE
:MEASure:AVERaging:COUNt
:MEASure:MHOLd
6-2
Function
Sets or queries the jump destination range that is used when a voltage peak
over-range occurs.
Queries all electric current measurement settings.
Sets or queries the current range.
Sets or queries the current auto range on/off state.
Sets or queries the valid current range.
Sets or queries the jump destination range that is used when a current peak
over-range occurs.
Sets or queries the valid external current sensor range.
Sets or queries the jump destination range that is used when a current peak
over-range occurs.
Queries the external current sensor conversion ratios of all elements.
Collectively sets the external current sensor conversion ratios of all elements. 6-14
Sets or queries the external current sensor conversion ratio of the specified
element.
Sets or queries the on/off state of the range configuration (valid range
selection) feature.
Queries all scaling settings.
Sets or queries the scaling on/off state.
Queries the VT ratios, CT ratios, or power coefficients of all elements.
Collectively sets the VT ratio, CT ratio, or power coefficient of all elements.
Sets or queries the VT ratio, CT ratio, or power coefficient of the specified
element.
Sets or queries the synchronization source.
Queries all input filter settings.
Sets or queries the line filter.
Sets or queries the frequency filter.
Queries the peak over-range information.
Sets or queries the check range status.
Queries all integration settings.
Sets or queries the integration mode.
Sets or queries the integration timer value.
Starts integration.
Stops integration.
Resets the integrated value.
Queries the integration status.
Sets or queries the MATH equation.
Queries all measured and computed data output settings.
Queries all averaging settings.
Sets or queries the on/off state of averaging.
Sets or queries the averaging type.
Sets or queries the averaging coefficient.
Sets the MAX hold on/off state.
Page
6-13
6-13
6-13
6-13
6-13
6-13
6-13
6-14
6-14
6-14
6-14
6-14
6-14
6-14
6-14
6-14
6-14
6-15
6-15
6-15
6-15
6-15
6-16
6-16
6-16
6-16
6-16
6-16
6-16
6-17
6-18
6-18
6-18
6-18
6-18
6-18
IM WT310E-17EN