YASKAWA P7 User Manual page 249

Mechanical Vibration .....................................................6-18
Mechanical Resonance ...................................................6-18
MENU Key ......................................................................3-3
Menu Trees, Digital Operator .............................. 3-7 to 3-13
Modbus Communications ........................ A-18, D-1 to D-13
(Also see Serial Communications)
Baud Rate...................................................D-2, D-4
Terminals...........................................................2-13
Mode Selection .................................................................3-4
Model Number ..................................................................1-4
Modified Constants (Parameters) Menu.................. 3-6, 3-13
Molded Case Circuit Breaker (MCCB) ........................... E-2
Momentary Power Loss Ride-thru ...... 5-11, 5-39, A-19, C-4
Monitor
Configuration ...........................................................5-50
Parameter List ....................................... 3-8, A-26, A-27
Power-On Monitor .........................................5-51, A-23
User Monitor .................................................A-23, A-24
MOP (Motor Operated Pot) Function ...................5-54, A-12
Reference Memory....................................................A-9
Motor
Auto-Tuning .............................................................5-59
Fault Displays & Processing.............................6-12
How to...............................................................5-59
Line-to-Line Resistance .................................. A-11
Menu ......................................................... 3-6, 3-13
Motor Rated Current ........................................A-25
Motor Rated Power ..........................................A-25
Direction........................................................... 4-7, 6-16
No-Load Current (NLA) ...............................5-32, A-11
Parameters ............................................................... A-11
Pre-Heat Current ............................................. 5-11, A-4
Protection .................................................................. C-4
Overheat...........................................................A-19
Overload...................................................A-19, C-4
Rated Current (FLA) ............ 4-6, 5-31, 6-12, A-11, B-4
Rated Voltage .................................................... 4-3, 4-5
Speed (U1-02) ........................................................A-26
Stopping Method Selection ....................... 4-7, 5-6, A-4
Temperature Input Filter Time ................................A-19
Troubleshooting .......................................... 6-14 to 6-19
Wiring ......................................................................2-21
Mounting, Inspecting ........................................................7-2
Multi-function Analog Inputs...................... 5-33, 5-38, A-16
Multi-function Analog Outputs ......................................A-17
Multi-function Digital Inputs .........................................A-12
Multi-function Digital Outputs.......................................A-15
Multi-step Speed Reference (Preset Speed) ............2-23, A-8
N
Nameplate Information ..............................................1-3, 1-4
NEMA Type 1 ...........................................................1-2, 1-4
No-Load Current (NLA) ...................................... 5-32, A-11
O
OFF Key ........................................................................... 3-4
Function during Remote Run ................................. A-24
Off-delay Timer .............................................................. A-5
On-delay Timer ......................................................... 5-9, A-5
Open Chassis..............................................................1-2, 1-4
Operation
Menu ...................................................................3-6, 3-8
Status (U1-12)......................................................... A-26
Operator Programming Errors (OPE) ............................. 6-11
Option
Card Faults..........................................................6-3, 6-4
Communication Error Selection .............................. 5-32
LonWorks Communication Setup............................ 5-32
Options (Peripheral Devices)............................................E-2
Orientation, Drive ........................................................... 1-14
Oscillation
Mechanical Vibration .............................................. 6-18
with PI control ......................................................... 6-18
with V/f control ....................................................... 6-18
Output
Current Monitor (U1-03) ........................................ A-26
Frequency – See Also Frequency, Output ..... C-2 to C-4
Ground Fault Detection Selection ................. 5-45, A-22
Monitors........................................................ A-26, A-27
Phase Loss ....................................................... 6-6, A-22
Power Monitor (U1-08) .......................................... A-26
Power Ratings – See Specifications, Standard Drive
.................................................................C-2 to C-4
Terminal Status Monitor (U1-11) ........................... A-26
Transistors (IGBT)
Inspecting ........................................................... 7-2
Spare Parts .................................................. F-2, F-3
Testing .............................................................. 6-22
Voltage Monitor (U1-06) ........................................ A-26
Outputs, Analog ............................................................. A-17
Outputs, Digital ............................................................. A-15
Over Current (OC) ............................................5-7, 5-45, 6-5
Overheat (OH)
Alarms/Faults................................... 5-45, 5-48, 6-5, 6-9
And Auto Restart ..................................................... 5-45
Cooling Fin (Heatsink) ......................5-49, 6-5, 6-9, C-4
Drive ....................................................................... A-22
Index - 5