Police (Qos) - Cisco Nexus 7000 Series Command Reference Manual

police (QoS)

S e n d d o c u m e n t c o m m e n t s t o n e x u s 7 k - d o c f e e d b a c k @ c i s c o . c o m .
police (QoS)
To configure policing of the data rates for a particular class of traffic, use the police command. To
remove a policing configuration, use the no form of this command.
Syntax Description
cir
cir-value
bps
kbps
mbps
gbps
percent
percent
bc
bc-value
bytes
kbytes
mbytes
ms
us
pir
pir-value
be
Cisco Nexus 7000 Series NX-OS Quality of Service Command Reference, Release 5.x
QOS-44
police [cir] {cir-value [bps | kbps | mbps | gbps] | percent percent} | [[bc] bc-value [bytes | kbytes
| mbytes | ms | us]] | | [pir {pir-value [bps | kbps | mbps | gbps] | percent percent} [[be]
be-value [bytes | kbytes | mbytes | ms | us]] | [conform {transmit | set-prec-transmit
precedence-value | set-dscp-transmit dscp-value | set-cos-transmit cos-val |
set-discard-class-transmit discard-class-value | set-qos-transmit qos-group-value} [exceed
{drop | set dscp dscp table cir-markdown-map}] [violate {drop | set dscp dscp table
pir-markdown-map}]]}
no police [cir] {cir-value [bps | kbps | mbps | gbps] | percent percent} | [[bc] bc-value [bytes |
kbytes | mbytes | ms | us]] | | [pir {pir-value [bps | kbps | mbps | gbps] | percent percent} [[be]
be-value [bytes | kbytes | mbytes | ms | us]] | [conform {transmit | set-prec-transmit
precedence-value | set-dscp-transmit dscp-value | set-cos-transmit cos-val |
set-discard-class-transmit discard-class-value | set-qos-transmit qos-group-value} [exceed
{drop | set dscp dscp table cir-markdown-map}] [violate {drop | set dscp dscp table
pir-markdown-map}]]}
(Optional) Sets the committed information rate as a bit rate or a percentage
of the link rate.
Committed information rate. The range of values is from 1 to 80000000000;
the range of policing values that are mathematically significant is 8000 to
80 Gbps.
(Optional) Specifies the units of bits per second.
(Optional) Specifies the units of kilobits per second.
(Optional) Specifies the units of megabits per second.
(Optional) Specifies the units of gigabits per second.
Specifies the percentage of the related parameter.
Specifies percent. Valid values are from 1 to 100.
Sets the committed burst rate, which is how much the cir can be exceeded,
either as a bit rate or an amount of time at cir.
Committed burst rate. Valid values are from 1 to 536870912. The default
value is 200.
(Optional) Specifies the units of bytes per second.
(Optional) Specifies the units of kilobytes per second.
(Optional) Specifies the units of megabytes per second.
(Optional) Specifies the units of milliseconds.
(Optional) Specifies the units of microseconds.
Sets the peak information rate.
Peak information rate. Valid values are from 1 to 80000000000; the range
of policing values that are mathematically significant is 8000 to 80 Gbps.
Specifies the extended burst rate. Valid values are from 1 to 536870912.
Cisco Nexus 7000 Series NX-OS Quality of Service Commands
OL-23378-01