GE D60 Instruction Manual page 244

5.5 FLEXLOGIC™
Table 5–9: D60 FLEXLOGIC™ OPERANDS (Sheet 8 of 10)
OPERAND TYPE OPERAND SYNTAX
ELEMENT: TELEPRO CH1 FAIL
Teleprotection TELEPRO CH2 FAIL
channel tests TELEPRO CH1 ID FAIL
TELEPRO CH2 ID FAIL
TELEPRO CH1 CRC FAIL
TELEPRO CH2 CRC FAIL
TELEPRO CH1 PKT LOST
TELEPRO CH2 PKT LOST
ELEMENT: TELEPRO INPUT 1-1 On
Teleprotection
inputs/outputs TELEPRO INPUT 1-16 On
TELEPRO INPUT 2-1 On
TELEPRO INPUT 2-16 On
ELEMENT TRIP 3-POLE
Trip output TRIP 1-POLE
TRIP PHASE A
TRIP PHASE B
TRIP PHASE C
TRIP AR INIT 3-POLE
TRIP FORCE 3-POLE
TRIP OUTPUT OP
TRIP Z2PH TMR INIT
TRIP Z2GR TMR INIT
ELEMENT TRIP BUS 1 PKP
Trip bus TRIP BUS 1 OP
TRIP BUS 2...
ELEMENT: WATTMETRIC 1 PKP
5
Wattmetric zero- WATTMETRIC 1 OP
sequence
WATTMETRIC 2...
directional
FIXED OPERANDS Off
On
INPUTS/OUTPUTS: Cont Ip 1
Contact inputs Cont Ip 2
Cont Ip 1
Cont Ip 2
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
current
(from detector on
form-A output only)
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
voltage
(from detector on
Cont Op 1
form-A output only)
Cont Op 2
INPUTS/OUTPUTS DIRECT INPUT 1 On
Direct inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: RemDPS Ip 1 BAD
Remote double- RemDPS Ip 1 INTERM
point status inputs
RemDPS Ip 1 OFF
RemDPS Ip 1 ON
REMDPS Ip 2...
INPUTS/OUTPUTS: REMOTE INPUT 1 On
Remote inputs
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
Virtual inputs
Virt Ip 64
5-110
OPERAND DESCRIPTION
Channel 1 failed
Channel 2 failed
The ID check for a peer relay on channel 1 has failed
The ID check for a peer relay on channel 2 has failed
CRC detected packet corruption on channel 1
CRC detected packet corruption on channel 2
CRC detected lost packet on channel 1
CRC detected lost packet on channel 2
Flag is set, Logic =1
↓
Flag is set, Logic =1
Flag is set, Logic =1
↓
Flag is set, Logic =1
Trip all three breaker poles
A single-pole trip-and-reclose operation is initiated
Trip breaker pole A, initiate phase A breaker fail and reclose
Trip breaker pole B, initiate phase B breaker fail and reclose
Trip breaker pole C, initiate phase C breaker fail and reclose
Initiate a three-pole reclose
Three-pole trip must be initiated
Any trip is initiated by the trip output
Phase distance zone 2 timer is initiated by the trip output
Ground distance zone 2 timer is initiated by the trip output
Asserted when the trip bus 1 element picks up.
Asserted when the trip bus 1 element operates.
Same set of operands as shown for TRIP BUS 1
Wattmetric directional element 1 has picked up
Wattmetric directional element 1 has operated
Same set of operands as per WATTMETRIC 1 above
Logic = 0. Does nothing and may be used as a delimiter in an equation list;
used as 'Disable' by other features.
Logic = 1. Can be used as a test setting.
On (will not appear unless ordered)
On (will not appear unless ordered)
↓
Off (will not appear unless ordered)
Off (will not appear unless ordered)
↓
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)
↓
VOn (will not appear unless ordered)
VOn (will not appear unless ordered)
↓
VOff (will not appear unless ordered)
VOff (will not appear unless ordered)
↓
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted while the remote double-point status input is in the bad state.
Asserted while the remote double-point status input is in the intermediate
state.
Asserted while the remote double-point status input is off.
Asserted while the remote double-point status input is on.
Same set of operands as per REMDPS 1 above
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
D60 Line Distance Protection System
↓
↓
↓
↓
↓
↓
↓
↓
↓
↓
5 SETTINGS
GE Multilin