Assigning Function To The User Buttons; Functions Assigned To User Buttons - Panasonic AU-EVA1E Operating Instructions Manual

Assigning function to the USER buttons

Selected function can be assigned to the USER buttons.
f The buttons that can be used as a USER button are as follows.
- <USER 1> to <USER 9> buttons
These can be used as the USER buttons when the VIEW screen is displayed.
- Multidial (when <WB>/<USER>/<ISO/dB> switch is set to <USER>)
1
From the [SYSTEM SETTINGS] menu → [USER SWITCHES] → [USER1] to [USER9] or [USER TOGGLE], select the function to
assign to each.
r Functions assigned to the USER buttons in the factory setting
USER button
<USER 1> button
<USER 2> button
<USER 3> button
<USER 4> button
<USER 5> button
<USER 6> button
<USER 7> button
<USER 8> button
<USER 9> button
Multidial

Functions assigned to USER buttons

Function assigned to <USER 1> to <USER 9> buttons
Item
[INHIBIT]
[AWB]
[ONE PUSH AF]
[ONE PUSH A.IRIS]
[ATW LOCK]
[E.I.S.]
[D.ZOOM]
[IR SHOOTING]
[REC SW]
[PRE REC]
[REC CHECK]
[DEL LAST CLIP]
[SLOT SEL]
[EXPAND]
[OPEN IRIS F.A.]
[PEAK./SQUARES F.A.]
[WFM]
[SPOT METER]
[ZEBRA]
[LEVEL GAUGE]
[LEVEL GAUGE SET]
[SDI COLOR]
[HDMI COLOR]
[LCD COLOR]
[LCD CLEAN VIEW]
[LCD MARKER]
[COLOR BARS]
[POWER LCD]
Chapter 3 Preparation — Assigning function to the USER buttons
[ONE PUSH AF]
[PEAK./SQUARES F.A.]
[SPOT METER]
[E.I.S.]
[WFM]
[AWB]
[SLOT SEL]
[EXPAND]
[OPEN IRIS F.A.]
[MONITOR VOL]
Disables assignment of functions.
Enables/disables the auto white balance.
Enables/disables the one-push auto focus.
Enables/disables the one-push auto iris.
Fixes the value of the white balance. Pressing the USER button again will resume the operation of the auto
tracking white balance.
f Enable when the auto tracking white balance is operating.
Enables/disables the electronic image stabilization function.
Enables/disables the digital zoom. It will zoom the angle of view 1.4 times both vertically and horizontally.
Enables/disables the IR recording.
Starts or stops the recording.
Enables/disables the pre-recording.
Automatically plays back the last approximately three seconds of the previously shot clip.
Deletes the clip last shot.
Selects the card slot with the SD card to record inserted.
Or, switches the card slot for the clip to display in the thumbnail screen.
Enables/disables the enlarged display function (focus assist function).
Enables/disables the open iris focus assist function (focus assist function).
Enables/disables the peaking function and focus square display (focus assist function).
The display is selected in the [OUTPUT SETTINGS] menu → [LCD FOCUS ASSIST] → [PEAK./
SQUARES MODE].
Switches the display of the waveform monitor. The waveform display is selected in the [OUTPUT
SETTINGS] menu → [LCD EI ASSIST] → [WFM MODE].
Displays/hides the spot meter.
This is enabled when the [OUTPUT SETTINGS] menu → [SDI/HDMI INDICATOR]/[LCD INDICATOR] →
[SPOT METER] → [ON] is set.
Displays/hides zebra patterns.
Displays/hides the level gauge.
Sets the current horizontal and vertical direction as the reference value of the level gauge.
Switches the output image from the <SDI OUT> terminal.
Switches the output image from the <HDMI> terminal.
Switches the output image from the <LCD> terminal.
Erases the display of the indicator or marker superimposed to the output video from the <LCD> terminal.
Displays/hides the marker superimposed in the output video from the <LCD> terminal.
Displays/hides the color bars.
Make it easier to view the LCD monitor in a well-lighted area such as outdoor.
Function
Description
– 53 –