Table of Contents
Advertisement
Screen display
VIEW screen
[ERROR HAS OCCURRED.
TO REPAIR THE CONTROL
DATA, PLEASE CONNECT
AC ADAPTOR OR CHANGE
BATTERY.]
[INVALID]
[Cannot record - Playlist capacity
is full.]
[Cannot copy - Playlist capacity
is full.]
[Exceeds capacity. Please
reselect.]
[Check the destination media.]
[NO SCENE FILE.]
[SCENE FILE LOAD FAILED]
[SCENE FILE WRITE FAILED]
[DISCONNECT USB CABLE.]
[CARD LOCKED.]
[CANNOT SELECT MORE
CLIPS.]
[SELECT THE CLIP TO BE
DELETED.]
[SELECT THE CLIPS TO COPY.]
[Insert a card in slot 1.]
[Insert a card in slot 2.]
[CHECK CARD.]
[CANNOT COPY.]
[Cannot add. The number of
accounts has reached maximum.]
[CANNOT RECORD.]
Chapter 9 Notes — Warning system
HOME screen
—
The remaining battery capacity was low when the
restoring of the management information is started.
—
Operation is disabled.
—
It has tried to record on the SD card which the
number of playlist that can be recorded has
reached the maximum.
—
It has tried to copied to the SD card which the
number of playlist that can be recorded has
reached the maximum.
—
The remaining recordable capacity of the copy
destination SD card is insufficient.
—
An error has occurred in the copy destination SD
card while copying.
—
There is no scene file in the read source SD card.
—
Reading of the scene file has failed.
—
Writing of the scene file has failed.
—
Due to an OS non-compatible error, five minutes
has elapsed until the USB service mode connection
is established.
—
It has tried to protect or delete a clip in the locked
SD card.
It has tried to copy a clip to the locked SD card.
—
It has tried to select more than 99 clips.
—
It has tried to delete a clip without choosing any.
—
It has tried to copy a clip without choosing any.
—
It has tried to copy without inserting the SD card
into the card slot 1.
—
It has tried to copy without inserting the SD card
into the card slot 2.
—
It has tried to copy to an error card.
—
It has tried to copy a content recorded in a AVCHD
format with a different system frequency (59.94 Hz
system or 50 Hz system) between the copy source
SD card the copy destination SD card.
—
Have tried to newly register a user account while
maximum number of user accounts (ten accounts)
are already registered.
—
Cannot be recorded.
Description
– 164 –
Behavior and cause
A message is displayed.
f Replace with a fully charged battery, or connect
the AC adaptor.
A message is displayed.
f Operate after the the operation becomes enabled.
A message is displayed.
f Replace the SD card or delete unnecessary clips.
A message is displayed.
f Replace the SD card or delete unnecessary clips.
A message is displayed.
f Reselect the clip to copy, or secure sufficient
remaining recordable capacity in the copy
destination SD card.
A message is displayed.
f Confirm the copy destination SD card.
A message is displayed.
f Insert an SD card that has a scene file.
A message is displayed.
f Check the SD card.
A message is displayed.
f Check the SD card.
A message is displayed.
f Confirm if the OS in use is supported by the
camera.
A message is displayed.
f Unlock the SD card.
A message is displayed.
f Execute the process such as copying by every 99
clips.
A message is displayed.
f Select a clip to be deleted.
A message is displayed.
f Select a clip to be copied.
A message is displayed.
f Insert an SD card into the card slot 1.
A message is displayed.
f Insert an SD card into the card slot 2.
A message is displayed.
f Check the SD card.
A message is displayed.
f Set the system frequency (59.94 Hz system or
50 Hz system) for the contents in the copy source
SD card and the copy destination SD card to be
the same.
f The system frequency information for the AVCHD
format is confirmed at the time of formatting or at
the first recording.
A message is displayed.
f Delete unnecessary user account.
A message is displayed.
f Perform recording after making it possible.
Advertisement
Table of Contents
