The Tx25A-80P Connector (Ops100-Sh) - DFI OPS100-SH User Manual

The TX25A-80P Connector (OPS100-SH)

The OPS+ Module enables the integration of a pluggable module and a display panel by
employing the defined interconnect based on the JAE and HRS combo plug and their receptacle
connectors. The right angle blind mate plug connector (p/n: JAE TX25A-80P-LT-H1E) should
be mated with the receptacle connector (p/n: JAE TX24A-80R-LT-H1E); together, they provide
interfacing for the following functions:
Power: DC-IN +12V~+19V@12A max
Display Interface: 2*HDMI 2.0 (or DVI or DP, 4K at 60Hz)
Audio: left and right Channel
USB: 1*USB 3.0 and 3*USB 2.0
Control and Sensors: 1*UART and Consumer Electronics Control (CEC, note that the OPS100-SH
does not support this function)
Control and Management Signals: the OPS+ Module power status, power-on via display panel,
OPS+ Module detect, system fan control, and device
The following table lists the pin assignments of the 80-pin JAE connector:
Pins Pin Assignment Description I/O
(1)
+12V~+19V Power -
40
+12V~+19V Power -
39
+12V~+19V Power -
38
37 +12V~+19V Power -
36 +12V~+19V Power -
35 +12V~+19V Power -
34 +12V~+19V Power -
+12V~+19V/NC Power/NC -
33
32 GND Ground -
31 DVI0_HPD DVI-D IN
30 DVI0_DDC_CLK DVI-D I/O
29 DVI0_DDC_DATA DVI-D I/O
28 GND Ground -
TMDS0_2+ DVI-D OUT
27
TMDS0_2- DVI-D OUT
26
Chapter 2 Hardware Installation
Chapter 5 Ports and Connectors
reset.
Pins Pin Assignment Description I/O
80 GND Ground -
79 GND Ground -
78 GND Ground -
77 GND Ground -
76 GND Ground -
75 GND Ground -
74
PWR_STATUS PowerGood OUT(OC)
73 PS_ON# Pluggable Signal ON IN
72 PB_DET Pluggable Board Detect OUT
71 Not Available Not Available I/O
70 AZ_LINEOUT_R Audio-R ch OUT
69 AZ_LINEOUT_L Audio-L ch OUT
68
GND Ground -
67 USB_PP0 USB I/O
66 USB_PN0 USB I/O
Chapter 5
GND
25
24 TMDS0_1+
23 TMDS0_1-
22 GND
21 TMDS0_0+
20 TMDS0_0-
GND
19
18 TMDS0_CLK+
17 TMDS0_CLK-
16 GND
15 DDP_HPD DisplayPort
14 DDP_AUXP DisplayPort
DDP_AUXN DisplayPort
13
12 GND
11 DDP_0P DisplayPort
10 DDP_0N DisplayPort
9 GND
8 DDP_1P DisplayPort
DDP_1N DisplayPort
7
(2)
6 GND
5 DDP_2P DisplayPort
4 DDP_2N DisplayPort
3 GND
2 DDP_3P DisplayPort
DDP_3N DisplayPort
1
Notes:
(1) The I/O column definition is in reference to the OPS+ pluggable board.
(2) OC= Open Collector.
28
Ground - 65 GND Ground
DVI-D OUT 64 USB_PP1
DVI-D OUT 63 USB_PN1
Ground - 62 GND Ground
DVI-D OUT 61 USB_PP2
60
DVI-D OUT USB_PN2
Ground - 59 GND Ground
DVI-D OUT 58 StdA_SSTX+ USB3.0
DVI-D OUT 57 StdA_SSTX- USB3.0
Ground - 56 GND
IN 55 StdA_SSRX+ USB3.0
54
I/O StdA_SSRX- USB3.0
I/O 53 GND Ground
Ground - 52 UART_TXD UART 3.3V
OUT 51 UART_RXD UART 3.3V
OUT 50 SYS_FAN System Fan Control
49
Ground - RSVD Reserved
48
OUT RSVD Reserved
OUT 47 RSVD Reserved
Ground - 46 RSVD Reserved
OUT 45 RSVD Reserved
OUT 44 RSVD Reserved
43
Ground - RSVD Reserved
42
OUT RSVD Reserved
OUT 41 RSVD Reserved
-
USB I/O
USB I/O
-
USB I/O
USB I/O
-
OUT
OUT
GND -
IN
IN
-
OUT
IN
OUT
-
-
-
-
-
-
-
-
-
www.dfi.com