Auto Leveling; Hitch Recognition - Lippert Components Ground Control TT Installation And Owner's Manual

Auto Leveling

1. Prior to auto leveling, ensure the trailer is unhitched
from the tow vehicle and the tow vehicle is parked a safe
distance away from the trailer.
2. Press the "ON/OFF" button (Fig.29L) if the OneControl
Touch Panel is not on.
3. Press "MyRV Control Panel" on the main screen (Fig.30A).
NOTE: On newer versions of the OneControl Touch Panel,
the screen will not open to "MyRV Control Panel." The screen
will open to "OneControl" with access to various functions,
including "Leveling." Choose "Leveling."
4. Press the "LEVELER" icon (Fig.31A).
5. Press "AUTO LEVEL" (Fig.29M).
NOTE: Once the automatic leveling cycle has been started,
it is important that there is no movement in the trailer until the
leveling process is complete. Failure to remain still during the
leveling cycle could have an effect on the performance of the
leveling system.
NOTE: Sequence may vary slightly based on the height of the
trailer coupler prior to leveling.
6. When the Auto Level Sequence begins:
A. The system checks that the rear jacks are retracted.
B. The Power Tongue Jack may adjust depending on the
orientation of the trailer.
C. Front jacks will extend until movement of the trailer is
sensed.
D. The Power Tongue Jack will then retract.
E. The front jacks will extend/retract near level.
F. Rear jacks will extend and ground.
G. Trailer will level front-to-back and then side-to-side.
H. The Auto Level Sequence will ground all jacks to ensure
all foot pads are on the ground.
I. The Auto Leveling sequence is complete when the
OneControl Touch Panel indicates, "Auto Level Success."
NOTE: If the AUTO LEVEL sequence does not perform
as described above, locate the OneControl Touch Panel
or use the OneControl App to place the system in Manual
Mode. Test that the jacks operate correctly by pushing
their corresponding buttons on the OneControl Touch
lippertcomponents.com 574-537-8900
Ground Control
Leveling OneControl
Touch Panel
Installation and Owner's Manual
(For Aftermarket Applications)
Panel or App; e.g., "FRONT" button operates only the front
jacks, etc. ("See Operation - OneControl Touch Panel" or
"Operation - OneControl App" in this manual).

Hitch Recognition

1. Press the "ON/OFF" button to turn the OneControl Touch
Panel on (Fig.29L).
2. Press "MyRV Control Panel" on the main screen (Fig.30A).
NOTE: On newer versions of the OneControl Touch Panel,
the screen will not open to "MyRV Control Panel." The screen
will open to "OneControl" with access to various functions,
including "Leveling." Choose "Leveling."
3. Press the "LEVELER" icon (Fig.31A).
4. Press "AUTO HITCH" (Fig.29N).
A. Rear jacks will retract.
B. The Power Tongue Jack will extend to the ground.
C. Front leveling jacks will retract.
D. The tongue jack will then adjust the height of the front of
the trailer coupler to the point at which the "AUTO LEVEL"
button was most recently pressed.
5. Back the tow vehicle into position to align the tow vehicle
hitch and trailer coupler with each other.
NOTE: If using the OneControl Touch Panel and the hitch
is not visible, a second person will be needed to monitor the
operation of the hitching process.
6. Press "RETRACT" button, then press the "FRONT" button
to retract the tongue jack until the coupler sets into position on
top of the tow vehicle hitch.
7. Latch the tow vehicle hitch and connect any wires, chains or
sway control that may be equipped between the tow vehicle
and trailer.
NOTE: Press the "RETRACT" button and then press and
hold the "FRONT" button until the Power Tongue Jack fully
retracts.
NOTE: To utilize the Power Tongue Jack for the hitching
process see "Operation - Power Tongue Jack."
18
Rev: 08.17 - GC
TT
®
TT Leveling OneControl
®
®
Touch Panel
®