Summary of Contents for Lippert Components Ground Control 3.0
Page 1
Ground Control 3.0 (5th Wheel) 4 Point and 6 Point OneControl Touch Panel OWNER'S MANUAL ™ Page 1 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Notes System Information Ground Control 3.0 is an automatic leveling system for 5th wheel applications. The system utilizes one main control board and a separate waterproof remote level sensor to measure and manage level point, and can be operated from several user interface devices, including: •...
Ensure the battery of the trailer is fully charged or that the trailer is plugged into shore power prior to attempting to operate the system. Ground Control 3.0 requires a minimum of 12.75V DC from the battery for proper operation.
Press "RETRACT ALL." (Fig. 1F). System will immediately retract all jacks. Use the quick release pins on the landing gear to manually return the inner jack leg to the fully retracted position. Page 4 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Power Button - Turns touch panel on and off. Auto Level - Starts the Auto Level sequence. Auto Hitch - Returns trailer to previous hitch height for reconnecting to tow vehicle. Page 5 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
NOTE: If the rear jacks will not operate individually using the method described above, but they operate properly when Auto Level is performed, the Twist Prevention Protection system has locked out the operation to prevent damage to the frame of the trailer. Fig. 3 Page 6 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Choose "ALL JACKS." Press “ENTER." System will immediately retract all jacks. 10. Use the quick release pins on the landing gear to manually return the inner jack leg to the fully retracted position. Page 7 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Extend - Extends jacks in several modes. Jacks available will be highlighted in blue. Auto Level - Starts the Auto Level sequence. Auto Hitch - Returns trailer to previous hitch height for reconnecting to tow vehicle. Page 8 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
"RETRACT" then press the “LEFT” (Fig. 6A) or “RIGHT” (Fig. 6C) button while simultaneously pressing the “FRONT" or "REAR” button (Fig. 6B and 6D), depending on which jack needs to be operated. Page 9 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Choose "ALL JACKS." Press “ENTER." System will immediately retract all jacks. Use the quick release pins on the landing gear to manually return the inner jack leg to the fully retracted position. Page 10 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Press any button in "Leveler" mode on the Linc Remote Control (Fig 7). Pressing "ABORT" on the OneControl Touch Panel (Fig. 11A) will cancel configuration sequence. Fig. 8 Fig. 9 Fig. 10 Fig. 11 Page 11 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
App; e.g., "FRONT" button operates only the front jacks, etc. (See "Operation - OneControl Touch Panel" or "Operation - OneControl App" in this manual). NOTE: There is no Hitch Recognition sequence programmed for the Linc remote. Page 12 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
"FUNCTION ABORTED" Hit OK. Restart the sequence. leveling sequence. Short circuit detected on one or "HALL POWER SHORT" more of the jack hall effect power Check harness and replace or repair. lines. Page 13 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
(open, short, malfunction or loss Right-Mid Jack Fault of communication); open or short Check fuses at controller. Left-Rear Jack Fault circuit between controller and motor. Right-Rear Jack Fault Repair or replace as necessary. Page 14 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Insert the ” socket into the port (Fig. 16). Turn the override until the jack extends or retracts to desired position. Fig. 12 Fig. 14 Fig. 13 Fig. 16 Fig. 15 Page 15 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Screen will show "Zero Point Stability Check ... Please Wait" (Fig. 21), followed by "Zero Point Set" (Fig. 22). Fig. 19 Fig. 17 Fig. 18 Fig. 20 Fig. 21 Fig. 22 Page 16 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
If jacks are down for extended periods, it is recommended to spray exposed leveling jack rods with a silicone lubricant every three months for protection. If the trailer is located in a salty environment, it is recommended to spray the rods every four to six weeks. Page 17 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
GROUND CONTROL 3.0 4 POINT ASSEMBLY ® Ground Control 3.0 4 Point Assembly LEVELING AND STABILIZATION Hall Effect Landing Jack Mounting Snapper Pin Hall Effect Jacks; Gear x2 Bracket x2 Jacks; Left Rear Right Rear Bolt On Pull Pin Jack Mounting Bolt &...
GROUND CONTROL 3.0 6 POINT ASSEMBLY ® Ground Control 3.0 6 Point Assembly LEVELING AND STABILIZATION Landing Jack Mounting Snapper Pin Hall Effect Jacks; Hall Effect Jacks; Gear x4 Bracket x4 Left Rear/Mid x2 Right Rear/Mid x2 Bolt On Pull Pin Jack Mounting Bolt &...
Hall Effect Jack; Rear Short 10.5" Stroke 343758 Hall Effect Jack Motor 119113 Bolt On Pull Pin 134989 Weld On Jack Mounting Bracket (OEM Only) 349975 Bolt On Jack Mounting Bracket (Aftermarket Only) Page 20 Rev: 03.02.2017 Ground Control 3.0 with OneControl...
Page 24
The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”). LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty. ...
Need help?
Do you have a question about the Ground Control 3.0 and is the answer not in the manual?
Questions and answers