Related Manuals for Lippert Components Project 2000 12600 Series
Summary of Contents for Lippert Components Project 2000 12600 Series
- Page 1 Euro Loft Bed Lift by Project 2000 OWNER'S MANUAL Page 1 Rev: 11.21.2014 Euro Loft Bed Lift by Project 2000 Owner's Manual...
-
Page 2: Table Of Contents
TABLE OF CONTENTS System and Safety Information Target Readers Purpose Of The Manual Compliance With Current Legislation Manual Preservation How To Obtain An Additional Copy Of The Manual User Information Manufacturer’s And Product Identification Data Technical Features Environmental Features Movement and Transport Prior to Installation Installation Mechanical... -
Page 3: System And Safety Information
System and Safety Information This manual will enable you to know and use your Euro Loft bed lifting system . Please read the manual carefully before using the system. The manual was written for users and/or product maintenance technicians and it is an integral part and of the product. -
Page 4: User Information
User Information This manual reflects the state of the art for the machine and cannot be considered unsuitable due to any possible updates related to new experiences. The manufacturer reserves the right to update production processes and manuals without the obligation to update previous production processes and manuals. - Page 5 The user shall guarantee that: All transport, connection, maintenance and repair operations are carried out by skilled and authorized staff. Skilled staff is understood as being (pursuant to IEC 364) the staff whose training, education, experience, information on law and regulations, accident prevention measures and terms of use and service, and who is able to carry out necessary operations recognizing and avoiding any possible danger and/or damage.
-
Page 6: Manufacturer's And Product Identification Data
Manufacturer’s And Product Identification Data MANUFACTURER: Project 2000 S.r.l. – Via Vivaldi, 40/A – IT 50041 Calenzano (FI) – VAT an tax No. 05025550483 BED LIFTING SYSTEM SERIES 12600 Technical Features Always refer to the identification plate on the product. Environmental Features Feature Value... -
Page 7: Prior To Installation
Prior to Installation All installation operations shall be carried out by skilled and authorized staff. Remove the product from packaging. Installation Mechanical NOTE: Always install the bed lifting system taking into account the system maximum load. THE BED UNIT AS A WHOLE - INCLUDING BED LIFTING SYSTEM, MATTRESS, PILLOW, BLANKETS, ETC. - MUST NOT WEIGH MORE THAN 60 KG. -
Page 8: Electrical
11. Place the limit switch correctly, making sure the bed locates against it perfectly when it comes to its highest position. NOTE: For bed lifting systems where the highest position is right under the vehicle roof or when the highest position more than 1500 mm from the floor, it is necessary to mount at least 2 opposed safety belts with internal micro-switch with normally closed contact. -
Page 9: Mechanical Encoder
Mechanical Encoder Fig. 2 Circuit Board Connection The circuit board is a controlling device equipped with: • DC 12 V, 25A maximum Working contact • DC 12 V, 25 A maximum motor output with polarity control Silkscreen Logic ID Range Clamps Description Printing... - Page 10 Move the bed upwards for a few centimeters, lower the bed and check the exact stop position: if it does not match the desired position, loosen the 14 mm bolt fastening the button and rotate the button to the extent that it is deemed necessary and try again to lift and lower the bed. Repeat the operation until the desired position is reached.
- Page 11 Fig. 4 Fig. 5 Silkscreen Logic ID Range Clamps Description Printing MOT2 DC 0-12 V Pin 5 Motor (Grey) MOT1 DC 0-12 V Pin 4 Motor (Brown) (C-3) Not used Pin 3 Not used Not used Pin 2 Not used Not used Pin 1 Not used...
- Page 12 Fig. 6 Page 12 Rev: 11.21.2014 Euro Loft Bed Lift by Project 2000 Owner's Manual...
- Page 13 The diagram in Fig. 6 summarizes all of the connections between the board and the other items that should be established in order for the system to work correctly. The motor connections (pin 3 and 7 of the 8-pole connector) and power connections (pins 4 and 8 of the 8-pole connector) must be carried out exactly as shown in the picture, be sure to use cables with a minimum section of 11/64".
-
Page 14: Security And Safety Devices
In these two situations the bed will not move because the pre-set end-of-stroke positions for operation are reached and it is not possible to overcome them. When operating the bed lifting system, clear operation area of children and obstructions or death, serious injury or property damage could occur. -
Page 15: Start-Up And Testing
Start-Up and Testing The product is delivered to the customer fully tested and ready for start-up. Start-up operations and product testing shall be carried out - once the system has been mounted on the vehicle - by specialized staff in order to reduce risks related to product start-up. -
Page 16: Maintenance Operations
Maintenance Operations Before starting maintenance operations, make sure the vehicle is parked and secured. After ascertaining vehicle stability, disconnect the electric system of the bed lifting system from the vehicle battery. Regular sight analysis of the belting and of the wall fastening elements (once a year) Check-up of motor and shafts coupling (once a year) Write on the “bed lifting system control register”... -
Page 17: General Information On Safety Regulations
General Information On Safety Regulations All dangerous equipment such as shafts, pulleys, chains, crown gears, etc. have been isolated and protected - within structural limitations - with suitable protection panels. The aforementioned panels, which effectively protect the user against dangerous components, shall not be removed, not even temporarily, and they shall be protected against interference throughout the bed lifting system life. - Page 18 Tab. A Tab. B Page 18 Rev: 11.21.2014 Euro Loft Bed Lift by Project 2000 Owner's Manual...
-
Page 19: Bed Lift Maintenance Log
Bed Lift Maintenance Log Bed Lifting System Control Register - Annex 1 Device Type Model Serial Number Manufacturing Year Checks Performed Year _________ Year _________ Year _________ Year _________ Year _________ Year _________ Year _________ Year _________ Year _________ Year _________ Five Yearly Check _________ Five Yearly Check _________ Five Yearly Check Date __________... - Page 20 Yearly Check Date __________ Number of Cycles _________ Are warning sound signals and lights working? Are the control devices for lifting and lowering the system working? Are the control devices for lifting and lowering the system clearly marked so that they can be correctly identified despite wear? Are there any clearances in the belt roller/s and the gear motor coupling? Is the gear motor perfectly working in all of its mechanical functions? Is the service breaking and parking system working?
- Page 21 Yearly Check Date __________ Number of Cycles _________ Are warning sound signals and lights working? Are the control devices for lifting and lowering the system working? Are the control devices for lifting and lowering the system clearly marked so that they can be correctly identified despite wear? Are there any clearances in the belt roller/s and the gear motor coupling? Is the gear motor perfectly working in all of its mechanical functions? Is the service breaking and parking system working?
- Page 22 The contents of this manual are proprietary and copyright protected by Lippert Components, Inc. (“LCI”). LCI prohibits the copying or dissemination of portions of this manual unless prior written consent from an authorized LCI representative has been provided. Any unauthorized use shall void any applicable warranty. ...