Basic Jack Operation; Unhitching From Tow Vehicle; Auto Level - Lippert Components Ground Control TT Installation And Owner's Manual

Basic Jack Operation

A. Press "EXTEND" (Fig.38E) or "RETRACT" (Fig.38A).
Press "Front" arrow (Fig.38B) to operate Power Tongue
Jack.
B. Press "AUTO LEVEL" (Fig.38H) to start auto level
sequence.
C. If the OneControl Touch Panel is in Manual Mode, to
operate jacks, press "EXTEND" (Fig.38E) or "RETRACT"
(Fig.38A) button, then press the "LEFT" (Fig.38C),
"RIGHT" (Fig.38F), "FRONT" (Fig.38B) or "REAR"
(Fig.38G) button depending on which pair of jacks need
to be operated.

Unhitching from Tow Vehicle

NOTE: Prior to unhitching from the tow vehicle, ensure the
trailer is parked on a level surface and chock the tires of
the trailer.
NOTE: Ensure the foot pad of the Power Tongue Jack is
pinned securely in place with the clevis pin and hairpin
cotter pin.
1. Disconnect any wires, chains, or sway control that
may be equipped between the tow vehicle and the trailer.
Unlatch the trailer coupler.
2. Turn the Linc remote on (Fig.38I) and enter a PIN code
to turn system on.
3. Press the "LEVELER" button.
4. Press "EXTEND" (Fig.38E) and "FRONT" arrow
(Fig.38B) to extend the Power Tongue Jack and lift the
front of trailer to take the weight of the trailer off of the
hitch.
5. Disconnect the trailer wire connection at the tow vehicle,
if not previously completed.
6. Pull tow vehicle away and park at a safe distance.
NOTE: To utilize the Power Tongue Jack for the unhitching
process see "Operation - Power Tongue Jack."
lippertcomponents.com 574-537-8900
Ground Control
Leveling OneControl
Touch Panel
Installation and Owner's Manual
(For Aftermarket Applications)

Auto Level

1. Prior to auto leveling, ensure the trailer is unhitched
from the tow vehicle and the tow vehicle is parked a safe
distance away from the trailer.
2. Press the "ON/OFF" button (Fig.38I) on the Linc Remote
if the Linc Remote is not on.
3. Enter a PIN.
4. Choose the "LEVELER" option.
5. Press "AUTO LEVEL" (Fig.38H).
NOTE: Once the automatic leveling cycle has been
started, it is important that there is no movement in the
trailer until the trailer has completed the leveling process.
Failure to remain still during the leveling cycle could have
an effect on the performance of the leveling system.
6. When the Auto Level Sequence begins:
A. The system checks that the rear jacks are retracted.
B. The Power Tongue Jack may adjust depending on the
orientation of the trailer.
C. Front jacks will extend until movement of the trailer is
sensed.
D. The Power Tongue Jack will then retract.
E. The front jacks will extend/retract near level.
F. Rear jacks will extend and ground.
G. Trailer will level front-to-back and then side-to-side.
H. The Auto Level Sequence will ground all jacks to
ensure all foot pads are on the ground and the Auto
Leveling sequence is complete.
NOTE: If the AUTO LEVEL Sequence does not perform
as described above, locate the OneControl Touch Panel
or use the OneControl App to place the system in Manual
Mode. Test that the jacks operate correctly by pushing
their corresponding buttons on the OneControl Touch
Panel or App; e.g., "FRONT" button operates only the front
jacks, etc. (See "Operation - OneControl Touch Panel" or
"Operation - OneControl App" in this manual).
NOTE: There is no Hitch Recognition sequence
programmed for the Linc emote.
25
Rev: 08.17 - GC
TT
®
TT Leveling OneControl
®
®
Touch Panel
®