Auto Level; Hitch Recognition - Lippert Components Ground Control TT Installation And Owner's Manual

NOTE: The touch pad will remain on as long as the user is
pressing buttons. It will time out after approximately 5 minutes
without use.
3. Press the "UP" arrow (Fig.28B) on the Auto Leveling Control
Touch Pad to extend the Power Tongue Jack and lift the front
of trailer to take the weight of the trailer off of the hitch.
4. Disconnect the trailer wire connection at the tow vehicle, if
not previously completed.
5. Pull tow vehicle away and park at a safe distance.
NOTE: To utilize the Power Tongue Jack for the unhitching
process see "Operation - Power Tongue Jack."

Auto Level

1. Prior to auto leveling, ensure the trailer is unhitched from the
tow vehicle and the tow vehicle is parked a safe distance away
from the trailer.
2. Press both "UP" and "DOWN" arrows
(Fig.28B and Fig.28C) at the same time if the green indicator
LED is not on.
3. Press "AUTO LEVEL" (Fig.28D).
NOTE: Once the automatic leveling cycle has been
started, it is important that there is no movement in the
trailer until the trailer has completed the leveling process.
Failure to remain still during the leveling cycle could have
an effect on the performance of the leveling system.
NOTE: Pressing any button during an Auto Level sequence
will abort the auto leveling cycle.
NOTE: Sequence may vary slightly based on the height of
the trailer coupler prior to leveling.
4. When the Auto Level Sequence begins:
A. The system checks that the rear jacks are retracted.
B. The Power Tongue Jack may adjust depending on the
orientation of the trailer.
C. Front jacks will extend until movement of the trailer is
sensed.
D. The Power Tongue Jack will then retract.
E. The front jacks will extend/retract near level.
F. Rear jacks will extend and ground.
lippertcomponents.com 574-537-8900
Ground Control
Leveling OneControl
Touch Panel
Installation and Owner's Manual
(For Aftermarket Applications)
G. Trailer will level front-to-back and then side-to-side.
H. The Auto level Sequence will ground all jacks to ensure
all foot pads are on the ground.
I. The Auto Leveling sequence is complete when the
indicator light turns solid green.
NOTE: If the "AUTO LEVEL" sequence does not perform
as described above, locate the OneControl Touch Panel
or use the OneControl App to place the system in Manual
Mode. Test that the jacks operate correctly by pushing
their corresponding buttons on the OneControl Touch
Panel or App; e.g., "FRONT" button operates only the front
jacks, etc. (See "Operation - OneControl Touch Panel" or
"Operation - OneControl App" in this manual).

Hitch Recognition

1. To turn on the Auto Leveling Control Touch Pad, press
both "UP" and "DOWN" arrows (Fig.28B and Fig.28C) at
the same time. The green indicator LED (Fig.28A) will turn
on.
2. Press "HITCH HEIGHT" (Fig.28E).
A. Rear jacks will retract.
B. The Power Tongue Jack will extend to the ground.
C. The front leveling jacks will retract.
D. The tongue jack will then adjust the height of the front
of the trailer coupler to the point at which the "AUTO
LEVEL" button was most recently pressed.
3. Back the tow vehicle into position to align the tow vehicle
hitch and trailer coupler with each other.
4. Press and hold the "DOWN" arrow to retract the tongue
jack until the coupler sets into position on top of the tow
vehicle hitch.
5. Latch the tow vehicle hitch and connect any wires,
chains or sway control that may be equipped between the
tow vehicle and trailer.
6. Press and hold the "DOWN" arrow until the Power
Tongue Jack is fully retracted.
NOTE: To utilize the Power Tongue Jack for the hitching
process see "Operation - Power Tongue Jack."
14
Rev: 08.17 - GC
TT
®
TT Leveling OneControl
®
®
Touch Panel
®