HPE FlexNetwork HSR6800 Configuration Manual page 265
Comware 7 layer 3, ip services
Hide thumbs
Also See for FlexNetwork HSR6800:
- Security command reference (538 pages) ,
- Configuration manual (482 pages) ,
- Command reference manual (153 pages)
Table of Contents
Advertisement
On Router A, configure the IPv6 address 1::1:0:0:1/96 for GigabitEthernet 2/1/1 and 1::2:0:0:1/96 for
GigabitEthernet 2/1/2. The lease duration of the addresses on subnet 1::1:0:0:0/96 is 172800
seconds (two days), the valid time is 345600 seconds (four days), the domain name is aabbcc.com,
and the DNS server address is 1::1:0:0:2/96. The lease duration of the addresses on subnet
1::2:0:0:0/96 is 432000 seconds (five days), the valid time is 864000 seconds (ten days), the domain
name is aabbcc.com, and the DNS server address is 1::2:0:0:2/96.
Figure 99 Network diagram
Configuration procedure
1.
Configure the interfaces on the DHCPv6 server:
# Specify an IPv6 address for GigabitEthernet 2/1/1.
<RouterA> system-view
[RouterA] interface gigabitethernet 2/1/1
[RouterA-GigabitEthernet2/1/1] ipv6 address 1::1:0:0:1/96
# Disable RA message suppression on GigabitEthernet 2/1/1.
[RouterA-GigabitEthernet2/1/1] undo ipv6 nd ra halt
# Set the M flag to 1 in RA advertisements to be sent on GigabitEthernet 2/1/1. Hosts that
receive the advertisements will obtain IPv6 addresses through DHCPv6.
[RouterA-GigabitEthernet2/1/1] ipv6 nd autoconfig managed-address-flag
# Set the O flag to 1 in RA advertisements to be sent on GigabitEthernet 2/1/1. Hosts that
receive the advertisements will obtain information other than IPv6 address through DHCPv6.
[RouterA-GigabitEthernet2/1/1] ipv6 nd autoconfig other-flag
[RouterA-GigabitEthernet2/1/1] quit
# Specify an IPv6 address for GigabitEthernet 2/1/2.
[RouterA] interface gigabitethernet 2/1/2
[RouterA-GigabitEthernet2/1/2] ipv6 address 1::2:0:0:1/96
# Disable RA message suppression on GigabitEthernet 2/1/2.
[RouterA-GigabitEthernet2/1/2] undo ipv6 nd ra halt
# Set the M flag to 1 in RA advertisements to be sent on GigabitEthernet 2/1/2. Hosts that
receive the advertisements will obtain IPv6 addresses through DHCPv6.
[RouterA-GigabitEthernet2/1/2] ipv6 nd autoconfig managed-address-flag
# Set the O flag to 1 in RA advertisements to be sent on GigabitEthernet 2/1/2. Hosts that
receive the advertisements will obtain information other than IPv6 address through DHCPv6.
[RouterA-GigabitEthernet2/1/2] ipv6 nd autoconfig other-flag
[RouterA-GigabitEthernet2/1/2] quit
2.
Enable DHCPv6:
# Enable the DHCPv6 server on the interfaces GigabitEthernet 2/1/1 and GigabitEthernet 2/1/2.
252
Advertisement
Table of Contents
Troubleshooting
