Canon LBP351 Series Service Manual page 164

Error Code Title
E245-1012 Host machine
FRAM write error
E245-1013 Host machine
FRAM write error
E245-1021 Host machine
FRAM write error
E245-1022 Host machine
FRAM write error
E245-1023 Host machine
FRAM write error
E245-2012 FLASH write error
E245-2022 FLASH write error
E246-0001 System error
E246-0002 System error
E246-0003 System error
E246-0004 System error
E246-0005 System error
E247-0001 System error
E247-0002 System error
E247-0003 System error
E247-0004 System error
E350-1001 System error
E350-1002 System error
E350-1003 System error
E350-3000 System error
E354-0001 System error
E354-0002 System error
E355-0001 System error
E355-0003 System error
E602-0001 Insufficient SD
Card capacity
E602-0002 Firmware error
E602-0003 SD Card access er-
ror
E602-0006 Firmware error
E602-0007 Firmware error
E602-0008 The memory area
in the Main Control-
ler is depleted.
E602-0009 MEAP cannot be
started.
E602-1102 File system could
not be initialized
normally (MEAP-
related).
Detection description
Host machine FRAM write er-
ror was detected.
Host machine FRAM write er-
ror was detected.
Host machine FRAM write er-
ror was detected.
Host machine FRAM write er-
ror was detected.
Host machine FRAM write er-
ror was detected.
FLASH write error was detec-
ted.
FLASH write error was detec-
ted.
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
System error
Capacity of the installed SD
Card is smaller than the size
of the area used for the sys-
tem.
Loading of Bootable ends in
failure.
Error caused by hardware
(such as damage on the sec-
tor, etc.) occurred when ac-
cessing to the SD Card during
execution of Boot ROM
Loading of Subbootable ends
in failure.
Damage on the internal file
Remaining memory area in
the Main Controller is small.
MEAP cannot be started due
to an error caused by invalid
power down.
File system could not be ini-
tialized normally (MEAP-rela-
ted).
1. Replace the Main Controller PCB.
1. Replace the Main Controller PCB.
1. Replace the Main Controller PCB.
1. Replace the Main Controller PCB.
1. Replace the Main Controller PCB.
1. Replace the Main Controller PCB.
1. Replace the Main Controller PCB.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
Contact the sales company.
1. Check the capacity of the SD Card. 2. Replace the SD Card with
another one with 2 GB or more capacity.
1. Reinstall the firmware. 2. Replace the Main Controller PCB.
1. Turn OFF and then ON the main power. 2. Back up data, and
format the SD Card. 3. Replace the SD Card. 4. Replace the Main
Controller PCB.
1. Reinstall the firmware. 2. Replace the Main Controller PCB.
1. Reinstall the firmware. 2. Replace the Main Controller PCB.
* Turning OFF and then ON the main power stops the error code to
be displayed, but the continuous use causes the memory area in the
Main Controller PCB to be completely used up or causes symptoms
such as machine freeze. 1. Replace the Main Controller PCB.
Select Function.gr > MEAP > MEAP FUNCTION = ON, and turn OFF
and then ON the main power. * Since the installed MEAP application
and its management information are all cleared after reboot, MEAP
needs to be reinstalled.
Turning OFF and then ON the main power executes auto recovery.
Since E616-0001 may be displayed in some cases, execute the
remedy for E616-0001. * When this error occurs, the firmware down-
loaded by the CDS Updater will be lost.
157
8. Error/Jam/Alarm
Remedy