Siemens SIPROTEC 4 7SJ61 Manual page 396

Functions, Settings, Information
F.2 Settings
Addr. Parameter
7101 FCT 79
7103 BLOCK MC Dur.
7105 TIME RESTRAINT
7108 SAFETY 79 ready
7113 CHECK CB?
7114 T-Start MONITOR
7115 CB TIME OUT
7116 Max. DEAD EXT.
7117 T-ACTION
7118 T DEAD DELAY
7127 DEADTIME 1: PH
7128 DEADTIME 1: G
7129 DEADTIME 2: PH
7130 DEADTIME 2: G
7131 DEADTIME 3: PH
7132 DEADTIME 3: G
7133 DEADTIME 4: PH
7134 DEADTIME 4: G
7135 # OF RECL. GND
7136 # OF RECL. PH
7137 Cmd.via control
7139 External SYNC
7140 ZONE SEQ.COORD. 79M Auto Recl.
7150 50-1
7151 50N-1
396
Function C Setting Options
79M Auto Recl. OFF
ON
79M Auto Recl. 0.50 .. 320.00 sec;
0
79M Auto Recl. 0.50 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. No check
Chk each cycle
79M Auto Recl. 0.01 .. 320.00 sec;
∞
79M Auto Recl. 0.10 .. 320.00 sec
79M Auto Recl. 0.50 .. 1800.00 sec;
∞
79M Auto Recl. 0.01 .. 320.00 sec;
∞
79M Auto Recl. 0.0 .. 1800.0 sec; ∞ 1.0 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0.01 .. 320.00 sec
79M Auto Recl. 0 .. 9
79M Auto Recl. 0 .. 9
79M Auto Recl. (Einstellmöglich-
keiten anwendung-
sabhängig)
79M Auto Recl. YES
NO
OFF
ON
79M Auto Recl. No influence
Starts 79
Stops 79
79M Auto Recl. No influence
Starts 79
Stops 79
Default Setting Comments
OFF 79 Auto-Reclose Function
1.00 sec AR blocking duration after
manual close
3.00 sec 79 Auto Reclosing reset
time
0.50 sec Safety Time until 79 is
ready
No check Check circuit breaker
before AR?
0.50 sec AR start-signal monitoring
time
3.00 sec Circuit Breaker (CB)
Supervision Time
100.00 sec Maximum dead time
extension
∞ sec Action time
Maximum Time Delay of
Dead-Time Start
0.50 sec Dead Time 1: Phase Fault
0.50 sec Dead Time 1: Ground
Fault
0.50 sec Dead Time 2: Phase Fault
0.50 sec Dead Time 2: Ground
Fault
0.50 sec Dead Time 3: Phase Fault
0.50 sec Dead Time 3: Ground
Fault
0.50 sec Dead Time 4: Phase Fault
0.50 sec Dead Time 4: Ground
Fault
1 Number of Reclosing
Cycles Ground
1 Number of Reclosing
Cycles Phase
none Close command via
control device
NO External 25 synchronisa-
tion
OFF ZSC - Zone sequence
coordination
No influence 50-1
No influence 50N-1
SIPROTEC 4, 7SJ61, Manual
C53000-G1140-C210-6, Edition 05.2016