Panasonic FP0R User Manual page 316

Num
Name
-ber
Basic function instruction
F137 Auxiliary
timer (16-bit)
Special instructions
F138 Hours, min-
P138 utes and sec-
onds to
seconds data
F139 Seconds to
P139 hours,
minutes and
seconds data
F140 Carry flag
P140 (R9009) set
F141 Carry flag
P141 (R9009) reset
F142 Watching
P142 dog timer
update
F143 Partial I/O
P143 update
F144 Serial data
communica-
tion control
F145 Data send
P145
F146 Data receive
P146
F145 Data send
P145
F146 Data receive
P146
F145 Data send
P145
F146 Data receive
P146
F145 Data send
P145
F146 Data receive
P146
F147 Printout
F148 Self-
P148 diagnostic
error set
F149 Message
P149 display
: Available, : Not available,
*1) The instruction is available for FP0 T32 (V2.3 or later) and FP-e.
*2) This instruction is available for FP0 V1.20 or later and FP-e.
*3) This instruction is available for FP-X V1.20 or later and FPΣ 32k type.
*4) This instruction is available for FP-X V2.50 or later and FPΣ V3.20 or later.
15-54
Ope-
Boo-
lean
rand
STMR S, D Turns on the specified output and
R900D after 0.01 s × set value.
HMSS
S, D Converts the hour, minute and second
PHMSS data of (S+1, S) to seconds data, and
the converted data is stored in (D+1, D).
SHMS S, D Converts the seconds data of (S+1, S)
PSHMS
to hour, minute and second data,
and the converted data is stored in
(D+1, D).
STC - Turns on the carry flag (R9009).
PSTC
CLC - Turns off the carry flag (R9009).
PCLC
WDT S The time (allowable scan time for the
PWDT system) of watching dog timer is
changed to "S" × 0.1 (ms) for that scan.
IORF D1, D2 Updates the I/O from the number
PIORF specified by "D1" to the number
specified by "D2".
TRNS
S, n The COM port received flag (R9038) is
set to off to enable reception.
Beginning at "S", "n" bytes of the data
registers are sent from the COM port.
SEND S1, S2, Sends the data to another station in the
PSEND
D, N network (MEWNET). (via link unit)
RECV S1, S2, Receives the data to another station
PRECV N, D in the network (MEWNET). (via link unit)
SEND S1, S2, Sends the data to the slave station as
D, N the MOD bus master. (via COM port)
RECV S1, S2, Receives the data from the slave station
N, D as the MOD bus master. (via COM port)
SEND S1, S2, Sends the data to the slave station of
D, N the MOD bus master, type II.
RECV
S1, S2, Receives the data from the slave station
N, D of the MOD bus master, type II.
SEND S1, S2, Sends the data to the slave station as
D, N the MEWTOCOL master. (via COM
port)
RECV
S1, S2, Receives the data from the slave station
N, D as the MEWTOCOL master. (via COM
port)
PR S, D Converts the ASCII code data in the
area starting with "S" for printing, and
outputs it to the word external output
relay WY specified by "D".
ERR n Stores the self-diagnostic error number
PERR (n: k100 "n" in (DT9000), turns R9000 on, and
to K299) turns on the ERROR LED.
MSG S Displays the character constant of "S" in
PMSG the connected programming tool.
: Not available partially
Description
5
5
*1
5
*1
1
1
3
5
5
*2
9
9
9
*3
9
*3
9
*4 *4
9
*4 *4
9
*3 *3
9
*3 *3
5
3
13