Yamaha F200B Service Manual page 558

Index
A.
Abbreviation ................................................0-5
Actuator, sensor, and switch.......................2-3
Adjusting the forward gear shim
(T1) thickness .........................................8-51
Adjusting the forward gear shim
(T2) thickness .......................................8-102
Adjusting the reverse gear shim
(T1) thickness .......................................8-106
Adjusting the reverse gear shim
(T2) thickness .........................................8-55
Adjusting the shift cable ..........................10-15
Adjusting the throttle cable......................10-15
Adjusting the trim sensor ..........................9-34
Adjusting the valve clearance .....................7-4
After test run .............................................10-8
Assembling the cylinder block...................7-95
Assembling the cylinder head ...................7-67
Assembling the forward gear .......... 8-27
Assembling the fuel filter assembly...........6-14
Assembling the gear pump assembly .......9-54
Assembling the
lower case.................. 8-26
Assembling the oil pan and
exhaust manifold.....................................9-24
Assembling the oil pump assembly...........7-77
Assembling the
oil seal housing .......... 8-27
Assembling the
propeller shaft assembly ............... 8-17
Assembling the propeller shaft
housing assembly ...... 8-18
Assembling the PTT motor .......................9-47
Assembling the reverse gear .......... 8-84
Assembling the shift bracket .......................9-4
Assembling the starter motor ....................5-72
Assembling the tilt ram..............................9-61
Assembling the trim ram ...........................9-62
Assembling the upper case.......................9-20
Assembling the vapor separator ...............6-41
Assembling the water
pump housing ............ 8-10
B.
Battery cable routing with house
(accessory) battery .................................3-18
Battery cable routing without
house (accessory) battery.......................3-16
Battery installation.....................................3-16
Battery requirement ....................................1-6
Bleeding the PTT unit ...............................9-40
Blowby gas reburning system ...................2-14
Bottom cowling................................ 5-18
i-1
,
8-35
, , ,
8-35 8-83 8-88
, , ,
8-35 8-84 8-88
,
8-22
, , ,
8-22 8-74 8-79
,
8-88
, , ,
8-13 8-67 8-70
,
9-12
Bracket unit........................................1-5
Bracket unit technical data ....................... 1-16
Break-in .................................................... 10-7
C.
Camshaft .................................................. 7-46
Canister, throttle body, and surge tank..... 6-26
Changing engine oil.................................. 10-9
Changing gear oil ................................... 10-11
Charging system....................................... 1-10
Charging unit and component .................. 5-50
Charging unit and starting unit....................A-9
Checking battery
(for electric start models) ...............10-4
Checking for cooling water leakage.......... 10-8
Checking propeller.................................. 10-15
Checking the air pressure sensor....5-57
Checking the
air temperature sensor ..................5-56
Checking the APS .................................... 5-29
Checking the APS circuit .......................... 5-30
Checking the armature (PTT motor)......... 9-46
Checking the armature (starter motor) ..... 5-71
Checking the brush................................... 9-46
Checking the brush holder and brush....... 5-71
Checking the cam position sensor............ 5-34
Checking the camshaft ............................. 7-50
Checking the canister ............................... 6-28
Checking the canister check valve ........... 6-23
Checking the check valve ......................... 6-40
Checking the clamp bracket anode .......... 9-32
Checking the compression pressure .......... 7-1
Checking the connecting rod big
end side clearance ................................. 7-88
Checking the connecting rod
small end inside diameter and
big end inside diameter .......................... 7-88
Checking the cooling water passage ........ 10-8
Checking the cooling water
passage cover anode ............................. 7-72
Checking the cooling water pilot hole ....... 10-4
Checking the crankcase bolt .................... 7-89
Checking the crankpin oil clearance......... 7-89
Checking the crankshaft ........................... 7-88
Checking the
crankshaft journal oil clearance .............. 7-91
Checking the cylinder block anode ........... 7-95
Checking the cylinder bore ....................... 7-86
Checking the cylinder head ...................... 7-62
Checking the cylinder head anode ........... 7-67
Checking the
drive shaft .................. 8-26
Checking the drive shaft bushing ............. 9-20
,
1-19
,
10-8
,
6-28
,
6-18
, , ,
8-35 8-83 8-88