Emerson Powerdrive F300 Reference Manual page 137

Parameter 08.063 24V Supply Input Destination
Short description Defines the destination parameter for the 24V input
Mode Open‑Loop
Minimum 0.000
Default 0.000
Type 16 Bit User Save
Display Format Standard
Coding RW, DE, PT, BU
See Digital I/O 01 Source/Destination (08.021).
Parameter 08.065 Relay 2 Source
Short description Defines the source parameter for the relay 2 output
Mode Open‑Loop
Minimum 0.000
Default 0.000
Type 16 Bit User Save
Display Format Standard
Coding RW, PT, BU
See Digital I/O 01 Source/Destination (08.021).
Parameter 08.071 Digital I/O Output Enable Register 1
Short description Displays the binary form of the DI/O output enable register
Mode Open‑Loop
0
Minimum
(Display: 0000000000000000)
0
Default
(Display: 0000000000000000)
Type 16 Bit User Save
Display Format Binary
Coding RW, PT, BU
The bits in the Digital I/O Output Enable Register 1 (08.071), Digital I/O Input Register 1 (08.072) and Digital I/O Output Register 1 (08.073) each
correspond with one digital I/O as shown below. The update rate of the individual bits in these registers differs depending upon the I/O.
DI/O Bit Function
1 0 Digital Input/Output
2 1 Digital Input/Output
3 2 Digital Input/Output
4 3 Digital Input
5 4 Digital Input
6 5 Digital Input
7 6 Relay Output
8 7 24V Supply Output
9 8 Safe Torque Off 1
10 9 Safe Torque Off 2
11 10 Keypad Run Button
12 11 Keypad Auxiliary Button
13 12 24V Supply Input
14 13 Keypad Stop Button
15 14 Relay 2 Output
16 15 Drive Reset Button
The Digital I/O Input Register 1 (08.072) is always active and shows the value in the Digital I/O State parameter for all digital I/O configured as inputs.
Bits in the Digital I/O Output Register 1 (08.073) can be used to control the digital I/O directly. The bits control the output directly and are not modified by
the corresponding Digital I/O Invert/Toggle function. The bits in the Digital I/O Output Register 1 (08.073) only control the corresponding digital output if
all the conditions below are met:
1. The corresponding bit in the Digital I/O Output Enable Register 1 (08.071) must be set to 1.
2. The digital I/O must be an output, or it must be an input/output and the corresponding Digital I/O Output Select parameter must be one.
3. The corresponding Digital I/O Source/Destination parameter is not as valid source (e.g. 0.000) and the drive has been powered-up or reset
since it was first selected.
If the above conditions are not met, the digital output is controlled by the normal logic.
Powerdrive F300 Parameter Reference Guide
Issue: 01.15.00
Maximum
Units
Update Rate
Decimal Places
Maximum
Units
Update Rate
Decimal Places
Maximum
Units
Update Rate
Decimal Places
Bit update rate
Input Register Output Register
2ms 250μs
2ms 250μs
2ms 2ms
250μs Not applicable
250μs Not applicable
2ms Not applicable
Bit always 0 2ms
Bit always 0 2ms
2ms Not applicable
2ms Not applicable
Background Not applicable
Background Not applicable
2ms Not applicable
Background Not applicable
Bit always 0 2ms
Background Not applicable
59.999
Drive Reset Read
3
59.999
Drive Reset Read
3
65535
(Display: 1111111111111111)
Background read
0
Output Enable Register
Background
Background
Background
Not applicable
Not applicable
Not applicable
Background
Background
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Not applicable
Background
Not applicable
137