Directions For Use - Cubicon Single Operation Manual

2. Directions for use

Please read thoroughly "Directions for use" prior to the printing and comply with it.
It contains the most importance things from operation manual and therefore you should comply with it
to prevent the printer failure or deterioration of printed object.
If you do not follow this direction, it causes the serious problem on print quality of printed object or
damage on the printer.
Please use the authorized filament which HyVISION SYSTEM provides.
* It is excluded from warranty in case of the breakdown caused by using 3
Please use the unsealed filament spool as soon as possible.
Filament
Keep your filament tightly wound on the spool and sealed.
* Using contaminated filament by humidity and dirty can cause the breakdown of printer
and printing quality problem.
After mounting the filament considering the spool rotation/ insertion direction, assure if the
Mounting and
spool door is closed.
Dismounting of
filament spool
Make sure if the filament is loosened on the spool during dismounting it.
Take notice of Extruder temperature setting.
Replacement of
* If the extruder temperatures are not set properly, nozzle blockage and filament grinding
Filament
can be occurred.
Loading &
When exchanging the new filament, take notice of Extruder temperature setting and remove
Unloading
residuals inside of nozzle
Heat up the extruder (nozzle)/ heated bed to fit the proper temperature of filament.
* The printing quality can be improved by configuration of optimal value acquired through
Temperature
user experience.
condition of
In case the temperature of filament is out of proper temperature range, bad printing quality
Extruder(Nozzle)
and breakdown of the printer such as carbonization, extruding failure, grinding, and warping.
and Heated bed.
Remove the print object after the heated bed cools down accordingly.
Regular maintenance of extruder condition and cleaning.
* The replacement of worn nozzles (Grinding) due to normal use is excluded from the
warranty service.
After heating up the Extruder and clean the external nozzle of Extruder with pure cotton
cloth.
Cleaning of
Pay attention not to damage the Extruder when cleaning the internal nozzle using Nozzle
Extruder and
Management Pin.
Nozzle
* Extruder failure can occur by improper use, so thoroughly become skilled.
Use the Nozzle Management Pin after separating the detachable Extruder to prevent the
damage to internal Extruder.
Do not repeat cooling and heating while the filament remains inside of the nozzle.
Be sure to turn off the power when separating or mounting the Extruder.
Separating/
Do not power down when the detachable Extruder is heating up.
Mounting of the
(It allows to separate the detachable Extruder right after the power down for maintenance/
detachable
replacement.
Extruder.
* It causes the damage to the internal circuitry because fan is not working.
Regularly manage the fixed Extruder such as cleaning.
Fixed Extruder
After separating the detachable Extruder, remove the contaminants of gear at the bottom of
the fixed Extruder and filament path.
Clean the contaminants with scraper or dried cotton cloth.
* The replacement of damaged heated bed such as peeling off the coating due to normal
use is excluded from the warranty service.
Cleaning the
heated bed.
Use the high purity acetone or water to clean the contaminated heated
* Do not use wet wipes because washing ingredient of some wet wipes can contaminate the
coating of heated bed.
Regular check-up the operation of the detachable Extruder and remove the contaminants
Autotilt
on the bed.
Preparation of AS Take a picture or video the malfunction status or inside of the printer or LCD Display.
request * Users need to clarify the situation as much as possible to proceed the repair service.
Copyright Reserved HyVISION System Inc.
This document is a general purpose operation manual and is subject to change without notice when necessary
for product improvements. HyVISION System does not take the responsibility for loss caused by any error in the
document or provisions and use of this document.
Cubicon Single Operation Manual
(150616,En)
rd
party filament.
bed.
4 / 44