Cubicon Single Operation Manual page 41

If you set the wrong option on the Cubicreator when slicing it cannot be printed well. Use the Cubicreator

to make sure that G-Code file is normal. If the print path which seems G-code appears to be an unusual
path, G-Code is incorrect.
The slicing through the Cubicreator cannot work well due to the wrong 3D Model. Open the original 3d

model through the Cubicreator, check if there is any problem on slicing or G-Code convertion3D and
determine whether the 3D model is ok using other 3D model inspection program.
Data may have been incorrectly saved in the SD card because of a security program or a virus. Check the

data, make the necessary correction and try again.
3) I cannot print with the PC connection.

Check to determine if there is any problem with the PC to printer connection via USB.

Check whether the Cubicon Single driver is installed in the PC. Install it if needed.
Confirm that the OS of the PC is supported by Cubicon.

If it is OSX(MAC OS), you should use the Cubicreator v2 for OSX, Baudrate of printer should be set as
115,200.
Check to determine whether the PC has been infected by a virus. Correct the problem and reinstall the

driver.
4) The filament is not extruded out of the nozzle.
Ensure that the filament is authentic.
Because some filament has the different temperature condition to the authorized filament or thermal

deformation it may cause the problem when extruding filament and therefore the Extruder can be broken
down. The failure of printer by using the unauthorized filament is excluded from the warranty service.
Confirm that the filament is seamlessly supplied. If the filament in the spool is twisted or bent, correct the

problem.
Twisted or wound filament may be cause the continuous problem, so it is recommended to discard it.
Contaminated Filament by humidity or dirt can be changed from the first opening.
Using this filament cause the malfunction such as blockage of the Extruder. Please use the opened

filament as fast as possible, secure the filament to the spool not to be wound and keep it in the vinyl for a
short period to prevent the humidity/dirt.
Make sure the thickness of supplied filament is too thick or thin. Please use the 1.6~1.9mm diameter of

filament for the accurate supply.
Using thin or thick filament may cause the malfunction such as getting jammed to the equipment.
In case the filament is twisted or jammed inside of the Extruder, it may cause the problem on the

extruding to stop extruding the filament.
The twist problem may be improved with decreasing the temperature of inside of the equipment.
Confirm that the detachable extruder part is properly mounted. If there is a mounting problem, an error

message may be displayed on the LCD screen.

Confirm that the temperature conditions of the filament in use and extruder of the printer are correct.
The nozzle may have been plugged. Clean the nozzle, referring to

Extruder and Nozzle".

Have the nozzle replaced by an authorized service technician. The nozzle is
5) The printed object does not adhere to the bottom (heating bed).
Confirm that the filament is authentic.

It may cause the malfunction of printer while printing because some filament is not stick to the heated
bed.
Contaminated Filament by humidity or dirt can be changed from the first opening.
Using this filament cause the malfunction such as blockage of the Extruder. Please use the opened

filament as fast as possible, secure the filament to the spool not to be wound and keep it in the vinyl for a
short period to prevent the humidity/dirt.
Clean the surface of the heat bed.

Do not use wet wipes because washing ingredient of some wet wipes can contaminate the coating of
heated bed.
Copyright Reserved HyVISION System Inc.
This document is a general purpose operation manual and is subject to change without notice when necessary
for product improvements. HyVISION System does not take the responsibility for loss caused by any error in the
document or provisions and use of this document.
Cubicon Single Operation Manual
"6.8.2. Cleaning of Detachable
(150616,En)
consumables.
41 / 44