Table of Contents
Advertisement
Quick Links
Cubicon Style (3DP-210F)
Quick Start Guide
∙ Please read the safety cautions carefully before using the product, and use the
product appropriately.
∙ This document is provided to ensure the safety of users and to prevent property
damage.
∙ The Quick Start Guide only provides information on how to unpack the package
and install it.
∙
please refer to the Operation Manual for more detailed information.
www.3dcubicon.com
Advertisement
Table of Contents
Related Manuals for Cubicon Style 3DP-210F
Summary of Contents for Cubicon Style 3DP-210F
- Page 1 Cubicon Style (3DP-210F) Quick Start Guide ∙ Please read the safety cautions carefully before using the product, and use the product appropriately. ∙ This document is provided to ensure the safety of users and to prevent property damage. ∙ The Quick Start Guide only provides information on how to unpack the package and install it.
-
Page 2: Safety Caution
Safety Caution Thank you for purchasing Cubicon Style Please read this ‘Safety Caution’ before using the printer and always follow the guideline provided. This guideline is provided to ensure the safety of users, prevent the injury of third parties and prevent damage to the printer. -
Page 3: Directions For Use
G-Code above) preparation. * Cubicreator must be set up for Cubicon Style (3DP-210F) Printer could be out of order if you set up software for other printers. Please use the authorized filament which HyVISION SYSTEM provides. * It is excluded from warranty in case of the malfunction or damages caused by using 3rd party filament which are not approved for Cubicon. -
Page 4: External Printer Parts
External Printer Parts The printer is packaged after LOT test of output conditions. This testing may leave traces of usage on the heating bed, nozzle, etc. Be assured that these are traces of testing, and that there is no problem with the product. Used for maintenance such as the filament replacement (loading / [1] Top door unloading) - Page 5 Internal Parts and Heated Bed [1] Teflon tube Path to feed the filament into the Extruder. (Be cautious not to bend it) [2] Extruder The part to move and extrude the molten filament. [3] Clean filter case The part to mount the clean air filter. [4] Heated Bed Bed platform to print out the object.
- Page 6 Part of the Extruder [E1] Filament insertion hole Hole to insert the filament into the Extruder through Teflon tube. [E2] Filament handle Handle to manually pull the filament out of the extruder or insert it. [E3] Mold fan Fan to flow the air into the molded object. [E4] Heated block cover Cover case to surround the nozzle heated block.
-
Page 7: Accessories Included With Package
* The type and specification of the accessories included in the part may be changed without notice to enhance the product. * Please use the Cubicon homepage or contact a distributor to purchase additional accessories. Using an unauthorized filament or part may cause damage to the product. Any problem related to the use of an unauthorized part will not be covered by the after-sales service. -
Page 8: Unpacking And Installation
Unpacking and Installation (1/4) Be careful when unpacking and installing the product, as excessive force or ripping can damage the content. Unpacking Pay attention not to damage the Drive cable of extruder or Teflon tube being pulled, bent, stabbed to affect the operation of extruder and filament feeding. ①... - Page 9 Unpacking and Installation (2/4) ④ Remove the Cable tie of Extruder – Cut two side cable ties of Extruder with scissors. Pay attention not to damage the driven belt when cutting the cable tie. Remove red colored two cable ties in figure. ⑤...
- Page 10 Unpacking and Installation (3/4) Mounting of Filament Spool ② Insert the spool holder into the hole at the rear of ① Prepare the filament spool to be used. printer. Cut off the filament fixing tape and remove the Please be careful not to be fallen out of the spool bending filament.
- Page 11 * Once powered on, main components regarding heating components will be checked up automatically. If “Cubicon Ready” becomes “Check SelfTestResult”, it is an indication that there could be an error in main component inside printer. When this happens, please do not start the operation of the printer until you make sure to check the components indicated as fail in Function Menu {Configuration>SeftTest Result}.
- Page 12 Operation and LCD Screen Information Emergency When there is an error occurred when operating the printer, you can stop Stop immediately by pressing power-off button located on bottom right corner. LCD screen & Menu button. [1] LCD It shows the current status of printer or menu. Menu’s position moving.
- Page 13 Teflon tube into inlet hole of the printer. *The number changes according to ambient temperature. If LCD scren shows that “Cubicon Ready” turns to “Check SelfTestResult”, it is an indication that there is an error in main component inside printer.
- Page 14 Thus, it takes some various experiences to optimize your printing quality. Cubicon Style and accompanying slicing program, Cubicreator can provide various users with best quality printing experiences.